防雷及接地安装工艺流程.docVIP

防雷及接地安装工艺流程 防雷及接地安装工艺流程提要：所有支架必须牢固，灰浆饱满，横平竖直。支架水平间距不大于1m，垂直间距不大于，各间距应均匀，允许偏差30mm。转角处两边的支架距转角中心不大于250mm 更多建筑学堂 防雷及接地安装工艺流程 （1）接地体： 接地体埋设深度不应小于，垂直接地体长度不应小于，相互之间间距不应小于5m。 接地体埋设位置距离建筑物不应小于，当接地装置必须埋设在距离建筑物出入口或人行道小于3m时，应在接地装置上面敷设50~90mm厚度沥青层，其宽度应超过接地装置2m。 接地体的连接应采用焊接，焊接处焊缝饱满并有足够的机械强度，不得有夹渣、咬肉、裂纹、虚焊、气孔等缺陷，焊接处的药皮应清理干净，刷沥青做防腐处理。 （2）接地干线： 接地干线应设有为测量接地电阻而预设的断接卡子，采用暗箱装入，同时加装箱门并做好标记。 （3）支架： 所有支架必须牢固，灰浆饱满，横平竖直。支架水平间距不大于1m，垂直间距不大于，各间距应均匀，允许偏差30mm。转角处两边的支架距转角中心不大于250mm。 支架应平直。水平度每2m检查段允许偏差3/1000，垂直度每3m检查段允许偏差2/1000，但全长偏差不得大于10mm。 （4）引下线暗敷设： 引下线圆钢直径不得小于12mm。 引下线必须在距地面~做断接卡子，断接卡子所用螺栓的直径不得小于10mm，并加装螺丝平弹垫。 利用结构主筋做引下线时，每处引下线不得少于2根，并做好标记。 （5）避雷网安装： 避雷网应平直、牢固，不应有高低起伏和弯曲现象，距离建筑物应一致。 避雷网弯曲处不得小于90?,弯曲半径不得小于圆钢直径的10倍。 避雷网的焊接长度应大于6D，双面焊，焊接处应清除药皮并刷防锈漆。 建筑物屋顶上的突出金属物，应与避雷网焊接成一体。 daily morning exercises or class-break setting-up exercise and discipline inspection and appraisal of public signs;2, daily cleaning and inspection;3, the daily student school appearance, dress, wearing school card check;4, the daily duty guide to the leadership class discipline three rounds.Weekly moral education work:L, the flag raising ceremony and the national flag speech under the flag raising ceremony held on Monday;2, every week a class meeting, the meeting;3, every week two exercises, cleaning and hygiene, behavior norms, attendance situation published cloth appraisal, and the issue of the code of conduct;;4, weekly work week.Monthly moral education work:1, at least once a month, the theme of education activities, to patriotism education, behavior norms of education as the focus, combined with major retreat day.2, the monthly class quantization assessment and class teacher assessment, selection of behavior for the standard model class.Moral education in each term:1, at the end of each semester to form three good student, outstanding student cadres, civilized student.2, at least once a semester, parents will be.,Student etiquette conven