汽车机械制图课件1的.ppt

第6章 机件的表达方法 ;6-1 视 图;⒉ 六个投影面的展开; 除后视图外，靠近主视图的一边是物体的后面，远离主视图的 一边是物体的前面。; ;;;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;A;6-2 剖 视 图;;;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;A;;④ 在剖视图上已经表达清楚的结构,在其它视图上 此部分结构的投影为虚线时,其虚线省略不画。 但没有表示清楚的结构，允许画少量虚线。;⒌ 几种结构不同的零件的剖视;对比下列各图，注意区别它们不同之点在什么地方。;; 对于一些具有空心回转体的机件，即使结构对称，但由于外形简单，亦常采用全剖视图 ;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;;解决办法：;B;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;画半剖视图时必须注意的问题： ;3）半剖视图中间应画细点划线，不应画成粗实线 ;4）半剖视图的标注方法与全剖视图的标注方法相同 ;B;B;适用范围：;2）需要同时表达不对称机件的内外形状时，可以采用局部剖视 ;3） 当对称机件的轮廓线与中心线重合， 不宜采用半剖视时。;A;5）表达机件底板、凸缘上的小孔等结构 ;画局部剖应注意的问题：; ② 波浪线不能穿空而过，也不能超出视图的 轮廓线。; ③ 当被剖结构为回转体时，允许将其中 心线作局部剖的分界线。;;A;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;⒉ 两相交的剖切平面（旋转剖）;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;☆ 标注方法：;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;⒊ 几个平行的剖切平面（阶梯剖）;;4、复合剖;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;6-3 断面图