奥迪A6轿车传感器标准值（Standard value of audi A6 car sensor）.doc

下载文档 降价啦

3
0
约1.8万字
约 24页
2017-07-15 发布于河南
举报
版权申诉
保障服务

奥迪A6轿车传感器标准值（Standard value of audi A6 car sensor）.doc

1、本文档共24页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

奥迪A6轿车传感器标准值（Standard value of audi A6 car sensor）

奥迪A6轿车传感器标准值（Standard value of audi A6 car sensor） Standard value of audi A6 car sensor Audi A6 1. Standard value of sensor of ANQ engine 1. Hall sensor The test conditions Specification values The diode test lamp is used to connect the terminals 1 and 2 of hall sensor terminals to start the engine The crankshaft diode test lamp flashes 1 times per turn Connect the digital multimeter to the sensor terminal 1 and grounding, turn the ignition switch to ON position, and measure the voltage From 4.5 V to 5.5 V [img, 252226] file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image1.jpg [/ img] 2. Engine speed sensor The test conditions Specification values Disconnect engine speed sensor, and measure the resistance between the terminals 1 and 3 of the engine speed sensor with a digital multimeter Ω 450 ~ 1000 [img, 316187] file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image2.jpg [/ img] 3. Inlet temperature sensor The test conditions Specification values Measure the resistance between terminal 1 and 2 of inlet temperature sensor At 30 ℃, Ω resistance at 1500 ~ 1500 80 ℃, Ω resistance at 275 ~ 275 [img, 275209] file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image3.jpg [/ img] 4. Oxygen sensor The test conditions Specification values Starting engine idle running, and measuring the voltage between the terminals 1 and 2 of the oxygen sensor connector with a digital multimeter 11 ~ 15 v Starting engine idling operation, measuring the voltage of oxygen sensor terminals 3 and 4 with digital multimeter From 0.4 V to 0.5 V [img, 300308] file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image4.jpg [/ img] 5. Air flow sensor The test conditions Specification values Remove the air flow sensor connector, screw the ignition switch to ON position, and measure the voltage between the terminal 2 of the air flow sensor and the grounding of the engine with a digital multimeter Accumulator voltage Remove the air flow sensor connector, screw the i