美能达复印机错误代码及解决方法（Error codes and solutions for mezzo copiers）.docVIP

下载本文档

66
0
约2.7万字
约 23页
2017-07-15 发布于河南
举报
版权申诉

美能达复印机错误代码及解决方法（Error codes and solutions for mezzo copiers）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

美能达复印机错误代码及解决方法（Error codes and solutions for mezzo copiers）

美能达复印机错误代码及解决方法（Error codes and solutions for mezzo copiers） Meiolda series photocopiers fail to solve the problem It has been able to troubleshooting for a series of copiers in 1054 (2030, 1050, 1080, 1052, 1080, 1085, 2010) 1. Phenomenon: C0F30 Cause: ATDC sensor damages Solution: the C0F30 code appears, such as the switch front door cannot be removed, and the ATDC sensor should be checked in the boot state to check whether the PWB - A has the signal output (pj10a-3 and GND) on the motherboard. If there is no output, check the wiring harness between the ATDC sensor and the motherboard. If there is signal output (the voltage between pj10a-3 and GND is between dc0.5v and dc4.5v), pwb-a can be determined to be damaged. The ATDC sensor has no output of PWB - A and the wiring harness is normal, and the ATDC sensor is damaged. Replace the ATDC sensor. 2. Phenomenon: operation panel does not show, adding powder function fails Cause: the IC2A (1176-6601-02) connected to the motherboard is invalid Solution: when the fault occurs, the machine should be memory clear (short circuit) operation first. If you cant rule out, then check the panel and power panel, the wiring harness of the main board and the ROM board (pwb-y) and the mainboard connection is reliable. In the normal condition of the above situation, the IC2A chip is checked and the fault is removed after the IC2A is replaced. Phenomenon: failure code C0000 Cause: the developer and the sensitive drum drive motor M2 damage. Solution: the C0000 code indicates that the main motor M2 turns the fault. You should see if the M2 turns when you press the copy key. If rotating, check whether the transmission part of the M2 motor is overloaded. If the above situation is normal, check the pwb-as pj11a-14a and the voltage from DC5V to DC0V by pressing the copy key. Pwb-a should be checked. Check if the voltage between pj11a-13a and GND on pwb-a remains DC5V by pressing the copy key. This should check the main motor M2. The driver