光钎放大器说明书（The optical bit amplifier specification）.docVIP

下载本文档

30
0
约1.15万字
约 15页
2017-07-21 发布于河南
举报
版权申诉

光钎放大器说明书（The optical bit amplifier specification）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

光钎放大器说明书（The optical bit amplifier specification）

光钎放大器说明书（The optical bit amplifier specification） Two calibration In this mode, the PV used will be the average value of the two sensing values obtained when there is no artifact. Press SET (SET) button when no workpiece is placed in front of the optical fiber module. Place an artifact in front of the fiber module and press the SET (setting) button. If the sensitivity is not enough space, after the calibration is completed, ____ will blink for about 2 seconds. Even in the In this case, the setting value will still be stored in memory. Percentage (%) calibration This calibration method can be set by reference to the percentage of light received when setting the sensitivity. For example, if the target value is SET to -10p, then the SET value ratio is determined when the SET (setting) button is pressed The received light is 10 % lower. Select the sensitivity setting method (item 2 on page 4), select % calibration, and then set the calibration target value. 2 refer to the required light intensity (usually not using artifacts), press the SET (setting) button. Other calibration (sensitivity setting) cannot be used when using % calibration. * use fs-v31c (P) / 32C (P) to periodically perform external calibration from PLC or other devices, even if There is a small sensitivity gap that can also be performed reliably. Set maximum sensitivity If it is a reflective workpiece, the sensitivity is set in the absence of the workpiece. If light passes through type workpiece, then Set up where the artifacts are placed In the state shown above, press the SET (SET) button for 3 seconds. The SET (SET) flashes the release button. When setting sensitivity, the set value should be slightly higher than the received light Full automatic calibration In this mode, PV will be set to the average value of the maximum and minimum associated values measured for a given time. Use this mode Detection of moving artifacts. Press the SET (Settings) button for at least 3 seconds while the artifact is pas