- 1、本文档共28页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
铜冲孔冲裁渐进模
摘 要
本设计题目为铜片冲孔落料级进模模设计,体现了冲孔落料类零件的设计要求、内容及方向,有一定的设计意义。通过对该零件模具的设计,进一步加强了设计者冲裁模设计的基础知识,为设计更复杂的冲裁模具做好了铺垫和吸取了更深刻的经验。
本设计运用冲压工艺及模具设计的基础知识,首先分析了工件的工艺要求,为选取排样的类型做好了准备;然后估算了板料的选取,便于导尺的宽度及确定排样的方法;最后分析了工件的特征,确定模具的设计参数、设计要点及自动漏料装置。
本工件为薄板的冲孔落料见,且工件的料厚较薄,所以在选取压力机是不宜过大,材料上说铜料的屈服强度也没有钢料的大,工件的尺寸较小设计时必须考虑设计一个能在冲孔落料时的剪切力小于材料的屈服强度以免冲裁力过大冲出废件。
关键词:冲裁模 冲裁 极限强度
Abstract
Blank and Prerce Grogressive Dies
This design topic hurtles bore to fall to anticipate class to enter a mold mold design for the copper, body now the blunt bore fall to anticipate a type of spare parts of design request, contents and direction, there is certain design meaning.Pass the design to the spare parts molding tool, strengthened designed further blunt cut the foundation knowledge of[with] mold design, for design more complicated of blunt cut a molding tool to have done cushion and absorbed deeper experience. This design usage blunt press the foundation knowledge of craft and molding tool design, analyzed the craft of the work piece a request first, have done preparation for the type that the selection lines up kind;Then the selection estimating plank to anticipate, easy to lead the method of the width and assurance row kind of Chinese foot;Analyzed the characteristic of work piece finally, make sure the design parameter, design important point of molding tool and leak to anticipate device automatically. This work piece falls to anticipate to see for the blunt bore of lamella, and the work piece anticipate thick thinner, so Be selecting by examinations pressure machine is should not lead greatly, say on the material the copper anticipates accepts defeat strength to also have no steel to anticipate of big, the size of work piece is smaller to design have to consider to design 1 can while hurtling the bore fall to anticipate of shearing and slicing the dint is small to accept defeat strength in the material in order to prevent blunt once cut dint to rush out to discard a piece greatly.Keyword: bl
您可能关注的文档
- 汽车电动执行器.ppt
- 沥青搅拌站管理规则.doc
- 沥青搅拌站操作程序.doc
- 沥青测试解释.ppt
- 沥青剥离剂.ppt
- 沥青混合料分级设计与应用.ppt
- 沥青砾石密封技术.doc
- 沥青和改性沥青.ppt
- 沥青稳定砂砾基地.doc
- 沥青路面监控.doc
- 中国行业标准 GM/T 0126-2023HTML密码应用置标语法.pdf
- 《JJF 2121-2024恒转速源校准规范》.pdf
- 餐饮服务中20条处理要点.docx
- 《GM/T 0011-2023可信计算 可信密码支撑平台功能与接口规范》.pdf
- 《JJF 2134-2024旋转流变仪校准规范》.pdf
- JJF 2121-2024恒转速源校准规范.pdf
- 计量规程规范 JJF 2121-2024恒转速源校准规范.pdf
- 《JJF 2118-2024压力式六氟化硫气体密度控制器校验仪校准规范》.pdf
- JJF 2134-2024旋转流变仪校准规范.pdf
- 计量规程规范 JJF 2134-2024旋转流变仪校准规范.pdf
最近下载
- 2011版课标“字表二 1000字“梳理.docx
- 电动吊篮安拆方案.doc VIP
- 2019中国消化道疾病检查白皮书(医疗).pdf
- 文心一言知识科普.pptx
- 2024年县民政局关于群众身边不正之风和腐败问题集中整治工作的形势分析报告.doc VIP
- 道路施工雨季安全培训.pptx
- (高质)《精神焦虑症的自救》.doc
- 港澳台联考语文满分作文.docx
- 单位办公室定密事项范围一览表式样.doc
- 理想 RISO 9050 7050 3050 7010 3010 闪彩印王中文技术维修手册 后面可以参考理想闪彩印王 EX7200 EX9050 EX9000 EX7250 系列中文维修手册 .pdf
文档评论(0)