51单片机智能环境监测系统程序.docxVIP

51单片机 智能环境监测系统程序王维进#include reg52.h#include intrins.h#include absacc.h#include math.h #include 0832.h#define uchar unsigned char#define uint unsigned int#include eeprom52.hsbit DATA = P3^7; //温湿度sbit E=P2^5;//1602使能引脚sbit RS=P2^7;//1602数据/命令选择引脚sbit RW=P2^6;sbit K1=P1^3;//设置键sbit K2=P1^4;//加sbit K3=P1^5;//减sbit K4=P1^7; //人体sbit K5=P1^6; //布防撤防按键sbit LED1=P3^1; //烟雾报警sbit LED2=P3^2; //温度上限sbit LED3=P3^3;//温度下限sbit LED4=P3^4; //湿度上限sbit LED5=P3^5; //湿度下限sbit LED6=P3^6; //红外报警sbit alarm=P3^0; //蜂鸣器uchar U8FLAG,U8temp,U8comdata,U8RH_data_H_temp,U8RH_data_L_temp,U8T_data_H_temp,U8T_data_L_temp,U8checkdata_temp;uchar U8RH_data_H,U8RH_data_L,U8T_data_H,U8T_data_L,U8checkdata;uchar Mode,humidity,temperature,smog;bit BJ_LED1=1,BJ_LED2=1,BJ_LED3=1,BJ_LED4=1,BJ_LED5=1,BJ_LED6=1;bit bdata FlagStartRH;uchar flag ;//记录当前设置状态uint count;//定时器0初始化void Timer0_Init(){ET0 = 1; //允许定时器0中断TMOD = 0x11; //定时器工作方式选择TL0 = 0xFF; TH0 = 0x4B; //定时器赋予初值TH1=0xdc;TL1=0x00;ET1=1;TR0 = 1; //启动定时器}//定时器0中断void Timer0_ISR (void) interrupt 1 using 0{uchar RHCounter;TL0 = 0xFF;TH0 = 0x4B; //定时器赋予初值RHCounter++; if (RHCounter = 15) { FlagStartRH = 1; RHCounter = 0; }}void Delay1(uint j){ uchar i; for(;j0;j--) { for(i=0;i27;i++); }} void Delay_10us(void){ uchar i; i--; i--; i--; i--; i--; i--;}void COM(void){ uchar i; for(i=0;i8;i++) { U8FLAG=2;while((!DATA)U8FLAG++);Delay_10us();Delay_10us();Delay_10us();U8temp=0; if(DATA)U8temp=1; U8FLAG=2;while((DATA)U8FLAG++);//超时则跳出for循环if(U8FLAG==1)break;//判断数据位是0还是1// 如果高电平高过预定0高电平值则数据位为 1 U8comdata=1;U8comdata|=U8temp; //0 }//rof}//--------------------------------//-----温湿度读取子程序 ------------//--------------------------------//----以下变量均为全局变量--------//----温度高8位== U8T_data_H------//----温度低8位== U8T_data_L------//----湿度高8位== U8RH_data_H-----//----湿度低8位== U8RH_data_L-----//----校验 8位 == U8checkdata-----//----调用相关子程序如下----------//---- Delay();, Delay