万用表最全使用方法（The most comprehensive use of a multimeter）.docVIP

下载本文档

8
0
约2.97万字
约 26页
2017-07-25 发布于河南
举报
版权申诉

万用表最全使用方法（The most comprehensive use of a multimeter）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

万用表最全使用方法（The most comprehensive use of a multimeter）

万用表最全使用方法（The most comprehensive use of a multimeter） We can use the R * 10 or R * 1 files of the multimeter to measure the quality of the PN junction in the road. In road measurement, measurement of positive and negative should have obvious characteristics of PN junction with R * 10 ohm (if it is not too obvious reverse resistance, can be used to measure the R * 1 ohm), generally positive resistance in R * 10 ohm measurement when the hands should be instructed in 200 ohm, R * 1 ohm measurement should be instructed in hand 30 ohm (according to the different phenotypes may be slightly different). If the measurement results are too positive or reverse resistance is too small, it shows that the PN junction is a problem, the tube will be a problem. This method is especially effective for maintenance, and it can be used to find out the broken pipes very quickly and even to detect tubes that have not been completely damaged but have deteriorated properties. For example, when you use a small resistance measuring deflection of PN junction forward resistance is too large, if you put it down with the welding commonly used R * 1K ohm test, may be normal, in fact, characteristics of this pipe has gone bad, can not work normally or unstable. 4, measuring resistance: it is important to choose the measuring range, when the pointer is indicated in the 1/3 to 2/3 full scale, the measurement accuracy is highest, the reading is most accurate. It should be noted that when using a R * 10K resistor to measure the large ohm resistance at the euro point, the fingers can not be pinched at both ends of the resistor, so that the resistance of the body will make the measurement result smaller. For the large imported plastic hose, the C is mostly in the middle (I havent seen B in the center yet). Medium and small power tubes, some B, most likely in the middle. For example, the commonly used 9014 transistor and other models of its series, transistors, 2SC1815, 2N5401, 2N5551 and other transistor