- 1、本文档共4页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
不同压头形状下板料渐进成形性能研究_许自然
2009 5 May 2009
2 8 5 MechanicalScienceandTechnologyforAerospaceEngineering Vo.l28 No.5
许自然,高 霖,崔 震,徐 岩
( , 2 100 16 )
:通过测量得到不同压头形状下的成形极限角、成形力与极限应变, 验研究板料在不同压
头形状下的渐进成形性能。得到了在不同压头形状下板料渐进成形性能的大小规律, 并分析不同
压头直径以及圆角半径对板料渐进成形性能的影响。结果表明:球头压头 (D6 R3 )的成形性能优
于具有同样圆角半径的平头压头 (D10 R3 ),平头带适当圆角的压头 (D10 R3 )的成形性能优于同直
径下的球头压头 (D10 R5 )。据此采用平头带圆角的压头成功成形出具有直壁小圆角的加强筋板
和浮雕字。
:渐进成形;成形性能;成形极限角
:TG386 :A :1003-8728 (2009 )05 -06 14 -04
InvestigationoftheForabilityofIncreental
SheetForingunderDifferentToolShapes
XuZiran, GaoLin, CuiZhen, XuYan
(CollegeofMechanicalandElectricalEngineering, NanjingUniversityofAeronauticsandAstronautic,sNanjing210016 )
Abstrac:tSallbatchesofproductscanbe anufacturedatalowcostandshortleadtiebyincreentalsheet
foringprocesswhichdoesnotrequirededicateddies.Seriesofstudiesonthe echanis andapplicationswere
donewhich adethisprocess oreapplicable.Butalltheresearcheswerecopletedbytoolswithspherical
shape,swhicharenotavailableforforingpartswithsharpcorner.sInthispape,rtheforabilityofincreental
sheetforingunderdifferenttoolshapeswasstudied.Theresultsshowthattheflattoolswithproperlowerradius
havebetterforabilitythanthesphericaltoolswiththesaediaete;rtheforabilityofflattoolsishigherthanthe
sphericaloneswiththesaelowerradiu.sFinally, thesheetbeadsandebossedcharacterswereforedsuccess-
fullybytheflattoolswithproperlowerradius.
Keywords:increentalforing;forability; axiu foringangle
, ,,
,、, ,
,, 、,
———。 。
,。 ,
, :
文档评论(0)