拨动开关的内部结构的焊接工艺（The welding process of the internal structure of the toggle switch）.docVIP

下载本文档

3
0
约8.25千字
约 5页
2017-08-03 发布于河南
举报
版权申诉

拨动开关的内部结构的焊接工艺（The welding process of the internal structure of the toggle switch）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

拨动开关的内部结构的焊接工艺（The welding process of the internal structure of the toggle switch） The welding process of the internal structure of the toggle switch When the internal resistance of the toggle switch can withstand high temperature (such as above 70 degrees Celsius), the power can be subjected to a significant decrease, so the circuit effect of two resistors in parallel will be better. Multiple resistance can be concluded that more ideal resistance through the combination of the resistance, such as 1.95 euro resistance than 2 the resistance in the actual application is more appropriate, if you want to buy a 1.95 euro resistance directly there is two 3.9 euro resistance is convenient, because 3.9 euro is the standard value, which is more than 1.95 euro. Jumper is used in the current loop, when after segmentation electrical ground plane, the shortest flow path fracture caused by signal. Toggle switch at this point, the signal circuits had to detour, form a large loop area, the influence of electric field and magnetic field is strong, easy to interference/be interference. It can be used to provide short reflux path and reduce interference. Configure circuit general, do not appear on the product to jump line and dial code switch. In order to reduce the maintenance cost, apply the 0 ohm resistance to the jumper wire and other welding on the board. Vacant jump line at high frequency is equal to the antenna, good other purposes, with effect of SMD resistor load resistance R = 200 euro, so for the power supply can output 100 v, so the current can only 0.5 A, toggle switch for electronic circuits, the voltage is not directly as the power of the semiconductor device, also must pass A smooth processing (filtering). Smoothing is actually in the half-wave rectifier circuit output by one capacitor using dc motor power type of electrical equipment, such as the half-wave rectifier output voltage ripple is enough but when ac voltage is half cycle, the ac power through the diode to pr