轧机前期改进工作（Early improvement work of rolling mill）.docVIP

下载本文档

1
0
约1.51万字
约 12页
2017-08-03 发布于河南
举报
版权申诉

轧机前期改进工作（Early improvement work of rolling mill）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

轧机前期改进工作（Early improvement work of rolling mill） Report on project work for Yellowstone 1. Emulsion system After the on-site inspection of the emulsion box and the internal nozzle of the mill, and the communication with the rolling oil manufacturer, the defect of the companys scratches has been basically solved, and the heat stroke has been saved. Suggestions for the current major problems are as follows: 1. Flow and pressure check and adjustment principle of emulsion system To frame the emulsion of each injection beam flow did not show, therefore, the current in the jet beam and a injection beam of each section of the flow is adjusted according to experience, no specific quantitative indicators. There is an electric valve (tape locator), manual ball valve and pressure gauge on each branch of the supply pipeline. Because flow cannot be detected, it is suggested to adjust the valve opening of each pipeline according to the pressure control method. In the case of pipeline, nozzle and other factors, the pressure and flow of the pipeline have corresponding relationship. The emulsion spray beam of baosteel 1730 mill is also controlled by pressure, which guarantees the supply of emulsion pressure, and the discharge flow is controlled. On site inspection, the pressure of each branch line is inconsistent, and there may be pressure gauges showing inaccurate problems, and there may be actual pressure and flow inconsistencies. For example, the pressure on the left side of the rolling lubrication and cooling tube road is in about 6bar, but the pressure on the right side of the pipeline is different. As shown in the photo, when rolling from right to left, the right side of the emulsion is put into use, and the three sections of pressure of the roll seam lubrication and cooling are shown respectively: 6bar, 0bar and 4.3 bar respectively. Proposed to gauge calibration, ensure correct display, adjust each branch pipe flow of emulsion (suggestion to adjust with manual valve, electri