精轧操作规程2（Finish rolling operation regulation 2）.docVIP

下载本文档

1
0
约2.65万字
约 34页
2017-08-04 发布于河南
举报
版权申诉

精轧操作规程2（Finish rolling operation regulation 2）.doc

1、本文档共34页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

精轧操作规程2（Finish rolling operation regulation 2） Three, finishing operation rules The start-up and shutdown procedures A boot: 1, the normal boot (mainly refers to the boot after maintenance) (1), check whether the device with rolling conditions (electrical, hydraulic, lubrication equipment, whether in place) Whether the power supply, the electrical measuring signal is normal, whether in the rolling position detection; Equipment: hydraulic cylinder, roll bending cylinder, oil cylinder, side guide, water cutting board, looper, water system in the work of the state; Hydraulic servo valve: normal, no leakage of hydraulic pipeline; The equipment lubricating grease: in place. (2), all equipment calibration is completed; (3), work roll, support roll cooling water; (4) under pressure, do light pressure signal to change after zero calibration; (5), all the conditions automatically, for steel rolling. On 2, after the change of work roll (1), after the completion of the work roll on, roll cooling water; (2), mill do light pressure, transfer zero calibration; (3), loop calibration, automatic descaling cast; (4), mill run to wait for speed; (5), all the conditions for all automatic rolling, ready to. 3, abnormal parking boot (mainly refers to the boot after processed scrap) (1), confirm the quick stop reset button; (2) after treatment, after careful examination of scrap equipment; (3), the mill do light pressure (according to the site can be calibrated to zero); (4), will run to wait for the speed of rolling mill; (5), all the conditions for all automatic rolling, ready to. Two, stop 1, normal conditions (1), lift pressure, pressure under the first limit; (2), roll on; (3), stop rolling mill; (4), looper rising; (5), roll cooling water 2, abnormal shutdown (1) when rolling, when an accident occurs, the operator immediately took quick stop; (2), take quick stop after all parking and roll mill steel seam automatic lift; (3), the scene and stage to deal with the scrap. Preparation a