炼钢厂氧气、乙炔安全管理规定（Regulations for the safety control of oxygen and acetylene in steelworks）.docVIP

下载本文档

4
0
约6.68千字
约 6页
2017-08-04 发布于河南
举报
版权申诉

炼钢厂氧气、乙炔安全管理规定（Regulations for the safety control of oxygen and acetylene in steelworks）.doc

1、本文档共6页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

炼钢厂氧气、乙炔安全管理规定（Regulations for the safety control of oxygen and acetylene in steelworks） Regulations for the safety control of oxygen and acetylene in steelworks Oxygen, steel plant, acetylene, management 1 oxygen 1.1 of the oxygen pipe network design, operation and maintenance, should conform to the requirements of GB50030 and GB16912; engaged in oxygen pipeline repair and maintenance and operations personnel, should be through the relevant safety and technical training, and pass the examination before induction. 1.2, the highest oxygen flow rate in the steelmaking workshop tubes: carbon steel pipe is not greater than 15m/s; stainless steel pipe is not greater than 25m/s. 1.3 the newly laid oxygen pipelines shall be degreased, rust removed and passivated. The oxygen pipeline shall be used again after maintenance and long-term deactivation, and shall be thoroughly blown with oil free compressed air or nitrogen. 1.4 oxygen pipeline valve, should use special valves; work pressure greater than 0.1MPa, should not use gate valve. 1.5 when oxygen pipes and oxygen bottles are frozen, they can be thawed by hot water or steam, and should not be thawed by fire or by hammer. 2 acetylene 2.1 acetylene station should meet the requirements of GB50031. The selection and installation of the electrical equipment shall comply with the requirements of the workshop of a production workshop. 2.2 when the working pressure of acetylene is 0.02 ~ 0.15MPa, the maximum flow rate in the pipe shall not exceed 9m/s. 2.3 the selection of acetylene pipes shall comply with the following provisions: Seamless steel pipe shall be used at medium pressure of 0.02 ~ 0.15MPa, and the inner diameter of the pipe shall be no more than 90mm; Medium pressure pipes greater than 50mm shall not use blind or dead ends and gate valves shall not be used. 2.4 the use of acetylene oxygen torch should be far away from the electrical cabinet, ignition should be near flammable and explosive materials. 2.5 the acetylene