上拉电阻下拉电阻耦合电容退耦电容的总结（Pull down resistor pull-up resistor capacitor decoupling capacitor summary）.docVIP

下载本文档

6
0
约1.6万字
约 13页
2017-08-18 发布于河南
举报
版权申诉

上拉电阻下拉电阻耦合电容退耦电容的总结（Pull down resistor pull-up resistor capacitor decoupling capacitor summary）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

上拉电阻下拉电阻耦合电容退耦电容的总结（Pull down resistor pull-up resistor capacitor decoupling capacitor summary）

上拉电阻下拉电阻耦合电容退耦电容的总结（Pull down resistor pull-up resistor capacitor decoupling capacitor summary） Pull-up resistor: 1, when the TTL driving circuit of COMS circuit, if the high level is lower than the minimum high level COMS circuit output TTL circuit (usually 3.5V), then you need to pull in the resistance of the output end of the TTL, in order to improve the output high level value. 2, OC gate circuit must be combined with pull resistors to use. 3, in order to increase the output pin drive capacity, and some SCM pins also often use pull-up resistor. 4, in the COMS chip, in order to prevent damage caused by static electricity, no feet can not be left hanging, generally connected to the pull resistor to reduce input impedance, providing leakage path. 5, the chip pins plus pull resistors to improve the output level, thereby increasing the chip input signal noise margin, enhance anti-interference ability. 6, improve the anti electromagnetic interference capability of the bus. It is easier to accept electromagnetic interference from the outside of the foot. 7, long line transmission in the resistance mismatch, easy to cause reflection wave interference, plus pull-down resistance is resistance matching, effectively suppress the reflection wave interference. The selection principle of the resistance value of the pull-up resistor includes: 1, from the power consumption and chip current capacity should be considered large enough, high resistance, small current. 2, from ensuring sufficient driving current should be considered small enough, small resistance, large current. 3. For high speed circuits, too large pull-up resistors may flatten at the edges. Comprehensive consideration The above three points are usually selected from 1K to 10K. There is a similar reason for pull-down resistors The selection of the pull-up resistor and the pull-down resistor should be based on the characteristics of the switching tube and the input characteristics of the lower circuit. The main facto