河南省211年普通高等学校对口招收中等职业学校毕业生考试机电与机制类基础课试题卷.doc

河南省20年普通高等学校对口招收中等职业学校毕业生考试 一、选择题（．A．B．C．D． 2．内燃机的配气机构采用的是 A．棘轮机构B．惰轮机构C．齿轮机构D．凸轮机构 ． A．B．C．D．． A．B．C．D．．A．B．C．D．．A．B．C．D．．A．B．C．D．． A．B．C．D．． A．B．C．D．． A．B．C．D．． A．B．C．D．．A．（a）B．（b） C．（c） D．（d）． 图2 A．B．C．D．．A．B．C．D．．A．B．C．．判断题（每小题分，共分。） 16．17． 18．19．．．．．．．．．．．．、名词解释题（每小题分，共分）．．．、题（小题，共分）．．．、小带轮直径和带轮包角？（6分） 37．．、题（小题，共分）．σ]=160MPa；AC杆材料为铸铁，直径40mm，许用应力[σ]=100MPa，试校核该结构的强度。（13分） 图6 40．图定轴轮系中蜗杆为双头左旋蜗杆，转向如图所示。蜗轮的齿数为，蜗杆2为单头右旋蜗杆，蜗轮3的齿数为其余轮齿数为，，，，。试求轮系传动比。（12分）。图7 机械制图（105分） 六、题（分）、题（小题，共分）在画出正确的螺柱连接图。（12分）、题（每空2分，共2分）图所示拨叉零件图，回答下列问题，将答案写在答题卡对应的横线上，写在试题卷上无效。 (1)该零件图采用_________视图和_________视图两个视图来表达零件的结构形状，为明确肋板的厚度采用了_________图。 (2)M18×1-6H螺纹孔的定位尺寸为_________、_________。它表示的是_________牙普通螺纹，_________，其大径为_________，螺距为_________。 (3)表示孔的基本尺寸为_________，上偏差为_________,下偏差为_________，公差为_________。 (4)图中表面要求最高的表面粗糙度Ra为_________。 图8 the same direction of rotation 90 ° or 180 ° for; after each disc rotor when measuring position alignment of the two half coupling constant, should also be in terms of accuracy and consistency. Surface deviation measurement, must in every 180 degrees corresponding to the two radii are equal to each other in order to eliminate errors caused by movement of the rotor. Only a support bearing of the rotor, WA couplings, such as the use of temporary leave the Center, should pay attention to keep the rotor in the measuring process in the center of the bearing oil retaining the nest does not change. Steam oil block, there should be sufficient clearance between the rotor and, in rotors make sure rotor is not on the block or seal oil. At the time of measurement, connections are not allowed between two rotors, each in a free State. Not allowed in case of assembled sleeve, Center work on the toothed coupling. Coupling tool should have adequate stiffness, installation must be secure and reliable. Coupling Center using a dial indicator, the table should be put in prison and avoid touching, to ensure correct measurement. Coupling disc after a week to return to the