长距离中压管线吹扫（Purging of long distance medium pressure pipelines）.docVIP

下载本文档

5
0
约1.43万字
约 27页
2017-08-24 发布于河南
举报
版权申诉

长距离中压管线吹扫（Purging of long distance medium pressure pipelines）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

长距离中压管线吹扫（Purging of long distance medium pressure pipelines）

长距离中压管线吹扫（Purging of long distance medium pressure pipelines） The selection of industrial metal pipe Specification for construction and acceptance of pipeline engineering (GB50235--97) as Standard purge scheme. 2.3 sweep methods and technical parameters calculation The way a regulator, torch torch storage method, storage regulator Blowing method. Blow the long pipeline, the construction period is relatively long, Tube sundries, selection of steam blowing combined with heat pipe, Received date: 2004 - 1O - 11; to date: 2005 - 12 O1. Author: Zhang Jimei (1962 -), male, engineer. 1981 graduated from the South Beijing School of chemical engineering and power. Tel: o533 7588447. 3O Qilu Petrochemical volume thirty-third By using the method of thermal targeting. Taking into account the debris tube has not be changed, improve blow The key lies in the quality of tube blowing technology parameters. by The choice of 1.5 ~ 2.5 to calculate the coefficient of wind pressure steam pipe And flow. Obviously, at the end of exposure to emissions from the initial conditions. End to end, with steam pressure drop, volume increase, pipe line The number is rising rapidly. As long as the initial end blowing momentum, can guarantee The entire pipeline has enough blowing momentum, therefore, only on the initial end Calculate. Design pressure: Ap0=0.4MPa Blowpipe drop: Ap=K * Ap0 = (1.5 ~ 2.5) * 0.4 =0.6 ~ 1 (M[E) a) Because of the prior condition can not determine the purge flow and the initial pressure of Relationship between the initial pressure is 0.6 ~ 1.5MPa, initial temperature 420 C, flow rate was 60 ~ 140t / h pipe coefficient were measured Numerical results are shown in Figure 1. Figure 1 4.3MPa steam pipeline blowing parameters Estimates show that the original pressure control in 0.8MPa, if Flow in the 80t / h, blowpipe coefficient was less than 1.5, the flow of To 120t / h, wind coefficient is 2.76 (Figure 1 represents only the same The relationship between the flow and the coeffi