华硕K4JC拆机清灰图解.doc

华硕K42JC拆机清灰图解 拆机有风险，请考虑清楚！拒绝暴力，一定要温柔！（图片手机拍的，效果不是太好） 注意：一定要记住怎么拆下来，在怎么装回去，废话不多说上图！ 圈圈里的是螺丝位置，螺丝最好分开放，不要把所有螺丝全放在一起。一定要记得哪些地方有螺丝，不然会出现清灰装上后，螺丝多出几颗！ 1、取下电池、拆内存盖、拆硬盘盖。 2、取下内存条（卡扣向两别剥） 3、取下硬盘（拧开4颗螺丝，向右平行挪动） 4、拆掉后盖上的其他所有螺丝。 5、取出光驱，拆掉下面的3颗螺丝。 6、拆完后，开始拆键盘，4个卡扣，注意键盘下面有连主板的排线! 7、取下键盘后，拆掉下图螺丝，下面还有一根触摸板连接主板的线，也拔下来 8、取下上盖后，就看见主板了。接着拆掉主板上的螺丝，拨开排线（如下图） 9、然后把主板提起来，其背面就能看到风扇。拆掉其6颗螺丝，拨开风扇的排线，就能取下风扇了。 10、拨开风扇的3个卡扣，就能打开风扇，自己把灰尘清理干净吧！ 11、如果硅脂干了，要重新涂上新的。（修电脑的地方有卖硅脂/导热膏的，不贵，几块钱） 重新组装上，哪儿怎么拆的就怎么重新装回去，记得各处的排线一定要连接上哦。 清完灰后，如果开机不能进系统，出现启动修复，怎么办？ 方法： 开机的时候，不停的按F2，直到进入bios设置界面。通过左右键选中“Advanced”，通过上下键选中“SATA Configuration”，回车进入下一个设置界面。 2、把AHCI模式改成IDE模式，如下图。 改成IDE后，按F10保存修改。然后重启，就能进入系统了！ 参考资料：/s/blog_bf94c4e001015x26.html the same direction of rotation 90 ° or 180 ° for; after each disc rotor when measuring position alignment of the two half coupling constant, should also be in terms of accuracy and consistency. Surface deviation measurement, must in every 180 degrees corresponding to the two radii are equal to each other in order to eliminate errors caused by movement of the rotor. Only a support bearing of the rotor, WA couplings, such as the use of temporary leave the Center, should pay attention to keep the rotor in the measuring process in the center of the bearing oil retaining the nest does not change. Steam oil block, there should be sufficient clearance between the rotor and, in rotors make sure rotor is not on the block or seal oil. At the time of measurement, connections are not allowed between two rotors, each in a free State. Not allowed in case of assembled sleeve, Center work on the toothed coupling. Coupling tool should have adequate stiffness, installation must be secure and reliable. Coupling Center using a dial indicator, the table should be put in prison and avoid touching, to ensure correct measurement. Coupling disc after a week to return to the original position, circumference of dial gauge reading should be able to go back to the original value. Whe