DJD2 PG电子经纬仪.docVIP

1 2  前 言 1、避免震动 保养总则  感谢您购买了 BOIF 电子经纬仪 DJD2-PG 系列，本仪器 是精密光电子测量仪器，维护和保养不善会使仪器精度降低， 寿命缩短，甚至会影响正常测量工作。为了使您更好地使用本 仪器，请您仔细阅读本说明书并妥为保存备用。 长途运输仪器时，最好进行外包装或考虑防震措施， 避免严重碰击仪器。 2、安装和迁站 仪器在三角架上安装时，要一手扶住仪器照准部，一 手旋转三角架中心螺旋，防止仪器滑落，卸下仪器时也应 如此。如果需要与三角架一起搬运仪器时，切不可水平方 向扛在肩上，应保持直立位置搬运仪器。如果距离较远时， 要取下仪器放在仪器箱内搬运。 3、保持清洁 仪器使用完毕后，要用绒布或毛刷清除仪器表面灰尘， 仪器被雨水淋后要及时擦干仪器。不可用化学擦拭剂擦洗 电池盒及塑料部件，如需要，可用浸水软布擦洗上述部件。 清洁外露光学件时，应用脱脂棉或镜头纸轻轻擦净，切不 可用手帕、衣服擦拭光学零件表面。 4、避免阳光长时间照晒仪器 仪器不要放置在极热的地点，或被阳光长时间照晒， 否则将影响仪器的测量精度。 5、检查电池 使用仪器前应检查电池电压，以保证仪器的正常使 用。 6、使用后须知 仪器使用后应保存在干燥、通风良好的室内，室温应 控制在 45℃以下，仪器包装箱应经常更换干燥剂。 3 4 目 录 一．用途···············································5 二．仪器各部位名称···································· 6 三．显示器和显示标记································· 8 四．操作面板和操作键································· 9 五．测量前的准备·····································10 1.安放仪器准备测量································ 10 2.开机···············································12 3.电压显示···········································13  八．数据输出及串行通信································26 1.RS—232C 串行通信接口····························26 2.数据输出···········································26 九．功能设置···········································27 1.功能设置···········································27 2.功能设置操作方法······························ 28 十．垂直角零位校正································· 31 十一．其它功能··········································33  4.更换电池···········································141.用十字丝测距···································33六．角度测量···········································152.倾斜改正功能···································341.水平角右旋增量和垂直角测量·······················153.照明和定时关机功能····························352.水平角右旋增量 HR 和左旋增量 HL 转换············16十二．检查和校正·····································363.水平角度设置·····································171.检查和校正长水准器·····························364.重复角度测量·····································182.检查和校正圆水准器·····························375.垂直角百分比测量模式（坡度角测量）··············203.十字丝竖丝的检验和校正························