雄兵启动型防盗器的安装全过程（The whole process of heroman start type anti-theft device installation）.docVIP

下载本文档

3
0
约1.04万字
约 8页
2017-09-21 发布于河南
举报
版权申诉

雄兵启动型防盗器的安装全过程（The whole process of heroman start type anti-theft device installation）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

雄兵启动型防盗器的安装全过程（The whole process of heroman start type anti-theft device installation）

雄兵启动型防盗器的安装全过程（The whole process of heroman start type anti-theft device installation） The whole process of heroman start type anti-theft device installation 2007-09-02 21:59, Pacific Auto Network Editor: wujianfeng Key words: start type anti-theft device installation process Look on the anti-theft device installation and alignment method of everyone, the younger brother to do for years in this trip, we will start the most complex two-way anti-theft anti-theft device in the installation by the whole process of writing, I hope useful for everyone. Heroman alarm installation 1, the first is ready to install the tool, and then check the instrument lights installed car and each line is normal, just make sure that everything is normal under the steering wheel cover. If you want to install a middle motor or a master console, you need to remove the trim panel for the lower door. 2, remove the need to install anti-theft device, the first joint platooninsert line with all host plugged in, then the wire harness order. When the tie line will be all bundled in thick wire harness on site. To make contact and elastic thread plug host where there was little nitrate telescopic, do not stretch too tight, so as not to loose due to traffic jitter. Then determine the location of the installation, and in the steering wheel under the junction box and the lock to find the corresponding wiring harness, measuring the length of the main wire harness. Some models still need to be found at the edge of the drivers seat. 3. First find the positive power line. Method for line: first the meter scale universal table dial to DC25V scale, and then use the test harness prick junction box or lock down, if the line. Will make the indicator test pencil light, and using the multimeter for measurement of DC12V, indicating that this line is for power line. The next available stripping knife line opened, the positive supply thick red parallel host line, with iron welding, and wrapped with insulation tape. 4.