多功能电子钟设计说明书.docVIP

多功能电子钟设计说明书 作品硬件原理图  三、程序流程图 四．程序源代码 1.dianz.h头文件代码 #ifndef __dianz_H__ #define __dianz_H__ sbit SD = P1^0; //串行数据输入 sbit ST_CK = P1^1; //存储寄存器时钟输入 sbit SH_CK = P1^2; //移位寄存器时钟输入 unsigned char code tab[]={0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f}; //列扫描 unsigned char code digittab[7][8]={ //字模取模方式 阴码 逆向 逐列式 {0x00,0x26,0x49,0x49,0x49,0x32,0x00,0x00},/*S,0*/ {0x00,0x00,0x00,0x48,0x7A,0x40,0x00,0x00},/*i,1*/ {0x00,0x78,0x08,0x08,0x78,0x08,0x78,0x00},/*m,2*/ {0x00,0xF8,0x48,0x48,0x48,0x48,0x30,0x00},/*p,3*/ {0x00,0x00,0x00,0x3E,0x40,0x20,0x00,0x00},/*l,4*/ {0x00,0x38,0x54,0x54,0x54,0x58,0x00,0x00},/*e,5*/ {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00}, }; unsigned char outwork[8]={0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00}; //屏显 unsigned char i,j,k,num;//变量 unsigned char cnta,cntb; void Ser_IN(unsigned char Data) //将8位二进制输入锁存器 { unsigned char i; for(i = 0; i 8; i++) { SH_CK = 0; //CLOCK_MAX=100MHz SD = Data 0x80; Data = 1; SH_CK = 1; } } void Par_OUT(void) //将锁存器中的数值输出显示在点阵上 { ST_CK = 0; ST_CK = 1; } void Go_dianzhen() { { if(cnta7){ // if(cntb8){ // for(i=0;i50;i++) { for(j=0;j8;j++) { Ser_IN(tab[j]); Ser_IN(outwork[j]); Par_OUT(); } //end for(j) } //end for(i) Ser_IN(0x00); Ser_IN(0x00); Par_OUT(); for(j=0;j7;j++) { outwork[j]=outwork[j+1]; } outwork[7]=digittab[cnta][cntb]; cntb++;}//end for(cnta) if(cntb==8) {cntb=0; cnta++;} }//end for(cntb) if(cnta==7)cnta=0; }//end while() } #endif 2..sing.h头文件代码 #include reg52.h sbit P1_3=P1^6; unsigned char code TABLE[]={0x82,0x01,0x81,0x94,0x84,0xB4,0xA4,0x04, 0x82,0x01,0x81,0x94,0x84,0xC4,0xB4,0x04, 0x82,0x01,0x81,0xF4,0xD4,0xB4,0xA4,0x94, 0xE2,0x01,0xE1,0xD4,0xB4,0xC4,0xB4,0x04, 0x82,0x01,0x81,0x94,0x84,0xB4,0xA4,0x04, 0x82,0x01,0x81,0x94,0x84,0xC4,0xB4,0x04, 0x82,0x01,0x81,0xF4,0xD4,0xB4,0xA4,0x94, 0xE2,0x