门架设施工程施工组织设计方案.docVIP

××××××××××门架设施工程 《施工组织设计方案》 ××××××××有限公司 20 年 月 日 目 录 一、 工程概述·····················································································3 二、 编制依据及执行标准·····································································3 三、 工程施工方案················································································4 四、 施工进度安排················································································劳动力计划···················································································主要施工机械设备··········································································制作························································································? 门架安装·······························································································································································10 十、 安全文明施工措施·······································································12 十一、工程质量保证措施·······································································16 十二、施工管理机构配置·······································································17 《施工组织设计方案》 工程概述： 1. 施工项目：×××××××××门架设施工程安装施工。 2. 工程地点及结构概况： 2.1××××××路×座跨度××米，净空高度××米门架； 2.2××××××路×座跨度分别是××米和××米，净空高度××米门架； 2.3××××××路×座跨度分别是××米、××米和××米，净空高度××米门架。 3. 工期要求：计划20××年××月××日开工，20××年××月××日竣工，总工期××个日历天。 4. 工程范围：按业主方招标文件工程量清单及对应施工图纸上涵盖的所有门架设施工作内容，本工程施工范围包括的现场现场安装施工。钢结构焊接规范(钢结构工程施工规范?GB 50755-2012)； 以及工程执行的现行国家、地方颁布的标准规范、规程及相关政策法规。 三、工程施工方案： 1. 施工准备??? 2. 组织有关工程管理和技术人员对设计图纸进行会审。对图纸不明确及施工中有困难的地方，要与设计单位作好变更鉴证手续 ??? 3. 根据施工图纸结合本单位的设备和技术条件，制定出工程的施工方案，并提出材料计划 ?? ?4. 对工程所使用的机械和检测设备的性能进行检验，保证施工过程中各种设备的工作状态良好，使用功能齐全  ???5. 门架工程所使用的材料除应有质量证明书外，还应符合标准方可使用 ? ?6. 门架工程施工前，应对各工序的施工人员进行必要的岗位培训，并对其进行技术、质量、安全交底，预防发生安全和质量事故 ? ?7. 现场吊装前，应在柱脚埋件上弹好十字线，同时将标高控制点设置好。现场场地应平整夯实，没有积水，并且要预留车道。 施工进度安排 ??? 按照工期要求，工程部分在土建施工的基础上保证工期计划，安排好施工进度，组织好施工具体进度计划见施工进度计划表施工进度计划表劳动力计划  按工程施工阶段投入劳动力下料工、 组立工 、焊工 、矫正工 、钻孔工 、 喷漆工 、电工 、起重工 、辅助工六、主要施工机械设备 ?? 1. 数控直条多头切割机 2半自动焊 2抛丸除锈机 摇臂钻 2 ； 电焊机 扭矩扳