KST-L型可曲饶双球体橡胶接头KST-Ldoublespheroid.DOC

KST-L型可曲饶双球体橡胶接头 KST-L double spheroid flexroidflexible rubber joint Page31 材料表 Table of Materilals 序号Serial No 部位Prtion 材料Material 1 主体Main body 极性橡胶polarized rubber 2 内衬Lining 尼龙帘布Nylon cord fabric 3 骨架Frame 尼龙帘布Nylon cord fabric 4 活接头Flexible joint 铸钢Mild steer 技术条件 Technical Consition 工作压力Mpa(kg.f/cm2)Workngpressnre 1.0Mpa(10kg.f/cm2) 偏转角度deflectangle (a1+a2)45℃ 爆破压力MPa(kg.f/cm2)Working pressure 3.0Mpa(30kg.f/cm2) 真空度Vacuum 53KPa(400mmHg) 适用温度Applecable temp.℃ -20~80℃ 适用介质 Applecable media 空气、压缩空气、水、海水、热水、弱酸Air.Compressed air. Water.Sea Water. Hot Water. Weak acid.Etc 注：+80℃-135℃采用特殊配方。 NOTE:+80℃-135℃ use special formula 注：安装时活接头中套必须压紧，以防软接头滑落 NOTE:Middle pipe of flexible rubber joint must be impacted tightly in order to avoid the joint slidingon installation 公称通径、长度、位移数值与法兰主要数据表 Table of Main Parameters of Nominal Core Diameter，Length，Displacement Value and Flange 公称能径Nominal core diameter L值(mm)LValue 轴向位移Axialdisplacenment(mm) 横向位移Axial displacenment(mm) （mm） (寸in) 伸长Strech(mm) 压缩Compression KST-15 1/2 200 5-6 22 22 KST-20 3/4 180 200 5-6 22 22 KST-25 1 180 200 5-6 22 22 KST-32 11/4 200 200 5-6 22 22 KST-40 11/2 210 200 5-6 22 22 KST-50 2 220 210 5-6 22 22 KST-65 21/2 245 220 5-6 22 22 KST-80 3 220 5-6 22 22 风机盘管连接件系列 Fan engine coiled pipes joint series 风机盘管连接件有不锈钢波纹管、紫铜波纹管和橡胶高压软管与钢制管路连接件扣压或链接而成。具有耐高压、弹性好、偏转位移量大、耐老化、耐温、安装方便，选择性好。适用于宾馆、饭店、办公楼、实验楼等各种风机盘管的进出口管路柔性连接。 Fan engine coiled pipes joint may be made of stainless steel corrugated pipe,red steel pipe and rubber soft pipe bearing high pressure burked of connected with steel or copper pipe.It has the feature of bearing high pressure,good flexible,large deviated displacement ,anti-aging ,anti-temperature and good selectivity.It is applied to flexible connective inlet and outlet pipe of fan engine coiled pipes in hotel,restarrant, office building and lab building. 技术条件 Technology qualification 工作压力working pressure 1.6MPa 爆破压力bursting pressure 4.8MPa 适