单片机制作的电压表程序.docVIP

单片机制作的电压表 #include reg52.h#include intrins.h#define uchar unsigned char#define uint unsigned intsfr ADC_CONTR=0xBC; //A/D转换功能允许寄存器sfr ADC_RES=0xBD;?? //A/D转换结果寄存器sfr ADC_RESL=0xBE; //A/D转换结果寄存器低sfr AUXR1=0xA2; //辅助寄存器1sfr P1_ASF=0x9D;??? //A/D转换控制寄存器sbit ADIO=P1^7;?????? //1.7口接测量电压sbit U3_DS=P1^5;sbit U3_STCP=P1^4;sbit U3_SHCP=P1^3; sbit U4_DS=P1^2;sbit U4_STCP=P1^1;sbit U4_SHCP=P1^0;uchar key_val[]={0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F,G};uchar code key_code[]={0x77,0x7B,0x7D,0x7E,0xB7,0xBB,0xBD,0xBE,0xD7,0xDB,0xDD,0xDE,0xE7,0xEB,0xED,0xEE};uchar key,count;void delay(unsigned int n);//74HC595void U3_595(unsigned char num)??? {?? unsigned char count1;?? for (count1=0;count1=7;count1++)?????? {?????? if ((num0x80)==0x80)//最高位为1，则向SDATA_595发送1????? {???????????? U3_DS=1;??? }???????????? else???? {???????????? U3_DS=0;??? }??? U3_SHCP=0;??? U3_SHCP=1;???????????? num=1;//左移??? }U3_STCP=0;U3_STCP=1;}void U4_595(unsigned char num)//发送指令到RS,RW,E(4,5,6位)??? {?? unsigned char count2;??? for (count2=0;count2=7;count2++)?????? {???????????? if((num0x80)==0x80)????? {???????????? U4_DS=1;??? }???????????? else??? {???????????? U4_DS=0;??? }???????????? U4_SHCP=0;??? U4_SHCP=1;?????? num=1;???? }??? U4_STCP=0;??? U4_STCP=1;}//LCD延时子程序 n=1时延时1msvoid delay(unsigned int n)?? { ????? unsigned char i;????? for(;n0;n--)????? for(i=0;i125;i++)???????? _nop_();}//写指令到LCDvoid wcmd(unsigned char cmd){??? U4_595(0x0F);U3_595(cmd);??? U4_595(0x4F);U4_595(0x0F);}//写要显示的数据到LCDvoid wdat(unsigned char dat){??? U4_595(0x1F);//低4位全为1屏蔽8段数码管?? U3_595(dat);U4_595(0x5F);U4_595(0x1F);}//初始化LCDvoid init(){??? wcmd(0x38);//设置8位总线双行显示，5*7点阵?? delay(20);wcmd(0x0C);//开显示，开光标，不闪烁delay(20);wcmd(0x06);//读写字符时地址加1delay(20);wcmd(0x01);//清屏delay(20);wcmd(0x82);}//键盘扫描子程序uchar keyscan(void){???? unsigned char hang,lie,keycode;char i;P0=0xf0;hang=P0;??? if((hang0xf0)!=0xf0)?????????? //有键按下？??? {??? delay(5);??