HCSE路由实验手册.docVIP

H3CSE路由实验配置 OSPF单区域配置： 从模拟器当中打开RT2和RT3两台路由器，按照如图所示配置接口IP地址，配置单区域的OSPF。 首先在RT2上进行配置： [H3C]sysname RT2 [RT2]interface Serial 0/2/2 [RT2-Serial0/2/2]ip address 10.1.1.1 24 [RT2-Serial0/2/2]quit [RT2]interface LoopBack 1 [RT2-LoopBack1]ip address 2.2.2.2 32 [RT2-LoopBack1]quit [RT2]ospf router-id 2.2.2.2 [RT2-ospf-1-area-0.0.0.0]network 10.1.1.0 0.0.0.255 [RT2-ospf-1-area-0.0.0.0]network 2.2.2.2 0.0.0.0 [RT2-ospf-1-area-0.0.0.0]quit [RT2-ospf-1]quit [RT2] 在RT3上的配置： [H3C]sysname RT3 [RT3]interface LoopBack 1 [RT3-LoopBack1]ip address 3.3.3.3 32 [RT3-LoopBack1]quit [RT3]interface Serial 0/2/0 [RT3-Serial0/2/0]ip address 10.1.1.2 24 [RT3-Serial0/2/0]quit [RT3]ospf router-id 3.3.3.3 [RT3-ospf-1]area 0 [RT3-ospf-1-area-0.0.0.0]network 10.1.1.0 0.0.0.255 [RT3-ospf-1-area-0.0.0.0]network 3.3.3.3 0.0.0.0 [RT3-ospf-1-area-0.0.0.0]quit [RT3-ospf-1]quit [RT3] 配置好之后在RT2上ping RT3发现可以ping通，那么实验配置就是正确的了。 [RT2]ping -a 2.2.2.2 3.3.3.3 PING 3.3.3.3: 56 data bytes, press CTRL_C to break Reply from 3.3.3.3: bytes=56 Sequence=1 ttl=255 time=24 ms Reply from 3.3.3.3: bytes=56 Sequence=2 ttl=255 time=14 ms Reply from 3.3.3.3: bytes=56 Sequence=3 ttl=255 time=25 ms Reply from 3.3.3.3: bytes=56 Sequence=5 ttl=255 time=10 ms --- 3.3.3.3 ping statistics --- 5 packet(s) transmitted 4 packet(s) received 20.00% packet loss round-trip min/avg/max = 10/18/25 ms 使用查看OSPF邻居状态的命令 [RT2]display ospf peer OSPF Process 1 with Router ID 2.2.2.2 Neighbor Brief Information Area: 0.0.0.0 Router ID Address Pri Dead-Time Interface State 3.3.3.3 10.1.1.2 1 36 S0/2/2 Full/ - 发现对端邻居3.3.3.3的状态已经是full状态了。 OSPF多区域实验： 打开模拟器的RT2、RT3和RT4，其中RT2和RT3在区域0，RT3和RT4在区域1，配置多区域的OSPF。 [H3C]sysname RT2 [RT2]interface Serial 0/2/2 [RT2-Serial0/2/2]ip address 10.1.1.1 24 [RT2-Serial0/2/2]quit [RT2]interface LoopBack 1 [RT2-LoopBack1]ip address 2.2.2.2 32 [RT2-LoopBack1]quit [RT2]ospf ro