郭天祥开发版自已开发写时钟.docVIP

//这里为了方便计算时间,我们假设晶振为12M.#includereg52.h//包含52单片机头文件#define uchar unsigned char #define uint unsigned intbit write=0; //写24C02的标志；sbit sda=P2^0; sbit scl=P2^1;void delay0(){ ;; }void start() //开始信号{ sda=1; delay0(); scl=1; delay0(); sda=0; delay0();}void stop() //停止{ sda=0; delay0(); scl=1; delay0(); sda=1; delay0();}void respons() //应答{ uchar i; scl=1; delay0(); while((sda==1)(i250))i++; //SCL在高电平期间，SDA被从设备拉为低电平表示应答。表示一段时间内没有收到从器件的应答则主器件默认已经收到数据而不再等待 scl=0; delay0();}void init_24c02()//IIC初始化函数{ sda=1; delay0(); scl=1; delay0();}void write_byte(uchar date)//写一个字节函数{ uchar i,temp; temp=date; for(i=0;i8;i++) { temp=temp1; scl=0; delay0(); sda=CY; delay0(); scl=1; delay0(); } scl=0; delay0(); sda=1; delay0();}uchar read_byte()//读一个字节函数{ uchar i,k; scl=0; delay0(); sda=1; delay0(); for(i=0;i8;i++) { scl=1; delay0(); k=(k1)|sda; scl=0; delay0(); } return k;}void write_add(uchar address,uchar date)//指定地址写一个字节{ start(); write_byte(0xa0); respons(); write_byte(address); respons(); write_byte(date); respons(); stop();}char read_add(uchar address)//指定地址读一个字节{ uchar date; start(); write_byte(0xa0); respons(); write_byte(address); respons(); start(); write_byte(0xa1); respons(); date=read_byte(); stop(); return date;}sbit dula=P2^6; //定义锁存器锁存端sbit wela=P2^7;sbit rs=P3^5; //定义1602液晶RS端sbit lcden=P3^4;//定义1602液晶LCDEN端sbit rw=P3^6;sbit s1=P3^0; //定义按键--功能键sbit s2=P3^1; //定义按键--增加键sbit s3=P3^2; //定义按键--减小键sbit rd=P3^7;sbit beep=P2^3; //定义蜂鸣器端uchar count,s1num;char miao,shi,fen;uchar code table[]= 2008-9-30 MON;//定义初始上电时液晶默认显示状态void delay(uint z) //延时函数{ uint x,y; for(x=z;x0;x--) for(y=110;y0;y--);}void di()//蜂鸣器发声函数{ beep=0; delay(100); beep=1;}void write_com(uchar com)//液晶写命令函数{ rs=0; rw=0; lcden=0; P0=com; delay(5); lcden=1; delay(5); lcden=0; }void write_date(uchar date)//液晶写数据函数{ rs=1; rw=0; lcden=0; P0=date; delay(5); lcden=1; delay(5); lcden=0; }void write_sfm(uchar add,uchar date)//写时分秒函数{ uchar shi,ge; shi=da