盾构机每日检查机械保环).docVIP

盾构机每日检查 TBM Daily Check 盾构型号 Shield Type 天气 Weather 温度 TEMP 工作种类： 机械 Job Class: Mechanical 地点 Location 操作描述：每日检查 Operation description?: daily checking 操作内容 Operations to realize PAGE 工作时间(s)- Working time (s) 特殊评论-观察Special remarks Observations :  要执行的工作-WORK TO EXECUTE?: 执行者 Done by 日期 Date 签名 Signature 检查日期-Checking date?: 执行者－Done by ?: 签名-Signature?: Page PAGE 1/ NUMPAGES 12 Shield body 盾构主体 S/N 序号 Check Points 检查项目 Remarks 备注 1 Any parts abnormal? 各部位的形状是否发生了异常 2 Any abnormalities in the mounting conditions of each apparatus? 各装置的安装状态是否发生了异常 3 Have the welds any cracks or other damage? 焊接部分是否发生了裂缝 4 Any abnormalities in the mounting of thrust jack spreaders? 运转部件附近是否堆积着土砂等杂物 Clean after each work 每次作业结束清理 5 Any earth and sand accumulated around spreaders and on the rods? 盾尾底部除去残留的水泥浆、杂质、石头、水和金属零件 Cutterhead and maindrive 刀盘和刀盘驱动 S/N 序号 Check Points 检查项目 Remarks 备注 1 All parts movement normally? 各部位的运动是否正常 2 Any looseness or cracks in the fitting portions? 装配部分是否发生了松弛或断裂 3 Lubricating oil supply sufficient? 润滑油供给是否充分 4 Any oil leaking from pipes? 配管是否有泄漏 Clean after each work 每次作业结束清理 5 Any vibration in pipes? 配管是否振动 6 Any abnormal sounds in main bearings? 刀盘轴承部位是否发生异常响动 7 Any abnormalities in gear and pinion? 齿轮、小齿轮部位是否异常 8 Leakage of centre revolving additives and hydraulic pipeline 中心回转接头管路是否有泄漏 9 Any abnormal sounds or overheating? 是否有异常的响动或发热 10 Any abnormalities in the rotation detectors? 旋转检测部位有无发现异常 Erector 拼装机 S/N 序号 Check Points 检查项目 Remarks 备注 1 Turning ring, gear and pinion teeth in good bite? 盘体与传动装置的齿轮啮合是否良好 2 Extension devices running smoothly? 液压油缸的运动是否流畅 3 Any abnormalities in jacks and the grip? 液压油缸、钳体等是否有异常 4 Any damages to connected hoses and cables? 连接软管、电缆是否有损伤 5 Any earth and sand accumulated on the turning ring? 盘体、导轨、轮子上是否有土砂附着或堆积 6 Stop block 限位装置是否正常 7 Warning light and alarm horn 报警灯和报警喇叭是否工作正常 Screw conveyor 螺旋输送机 S/N 序号 Check Points 检查项目 Remarks 备注 1 Is screw shaft operation normal? 螺旋轴运转是否正常 2 Has the dri