gb92531~925371988石油用螺纹gb国标系统.docVIP

中华人民共和国国家标准 GB9253.1～9253.7-88 石油用螺纹 THREADS FOR PETROLEUM INSUSTRY 技术科 TECHNICAL DEPARTMENT 重庆新泰机械有限责任公司 CHONGQING XINTAI MECHINERY LTD.  图1：三角形螺纹尺寸 注： 1、机紧时，接箍或内螺纹的端面可紧至消失点平面； 2、对于井下工具的螺纹螺尾角度可按实际需要确定。 图2：偏梯形形螺纹尺寸 表1 套管圆螺纹尺寸(CSG) 螺纹代号 大端大径D4 基准距离L1 有效螺纹长度L2 管端至消失点平面螺纹全长L4 基面中径E1 机紧后管端至接箍中心平面距离J 接箍端面至基面的距离M 接箍端孔直径Q 接箍端孔深度q 完整螺纹最小长度Lc 手紧紧密距压数A 适用的套管重量kg/m 4-1/2-Ⅰ 114.3 23.39 43.56 50.80 111.846 28.6 17.88 116.7 12.7 22.22 3 14.10 4-1/2-Ⅱ 114.3 39.27 59.44 66.68 111.846 12.7 17.88 116.7 12.7 38.10 3 15.60～22.5 5-Ⅰ 127.0 36.09 56.26 63.50 124.546 19.0 17.88 129.4 12.7 41.27 3 17.10 5-Ⅱ 127.0 42.44 62.61 69.85 124.546 12.7 17.88 129.4 12.7 41.27 3 19.30～35.90 5-1/2 139.7 45.62 65.79 73.02 137.246 12.7 17.88 142.1 12.7 44.44 3 20.80～34.20 6-5/8 168.3 51.97 72.14 79.38 165.821 12.7 17.88 170.7 12.7 50.80 3 29.80～47.60 7-Ⅰ 177.8 32.39 53.09 60.32 175.346 31.8 17.88 180.2 12.7 31.74 3 25.30 7-Ⅱ 177.8 51.97 72.14 79.38 175.346 12.7 17.88 180.2 12.7 50.80 3 29.80～56.60 7-5/8 193.7 53.44 75.31 82.55 191.114 12.7 18.01 196.1 12.7 53.97 3-1/2 35.70～70.10 8-5/8-Ⅰ 219.1 47.09 68.96 76.20 216.514 22.2 18.01 221.5 12.7 47.62 3-1/2 35.70 8-5/8-Ⅱ 219.1 56.62 78.49 85.72 216.514 12.7 18.01 221.5 12.7 57.14 3-1/2 41.70～72.90 9-5/8-Ⅰ 244.5 56.62 78.49 85.72 241.914 12.7 18.01 246.9 12.7 57.14 3-1/2 48.10～79.60 = 1 \* GB3 ① 9-5/8-Ⅱ 244.5 54.91 78.49 85.72 241.808 12.7 18.11 246.9 12.7 57.14 4 64.70～79.60 = 2 \* GB3 ② 10-3/4-Ⅰ 273.0 40.74 62.61 69.85 270.489 31.8 18.01 275.4 12.7 41.27 3-1/2 48.70 = 1 \* GB3 ① 10-3/4-Ⅱ 273.0 59.79 81.66 88.90 270.489 12.7 18.01 275.4 12.7 60.32 3-1/2 60.30～82.60 = 1 \* GB3 ① 10-3/4-Ⅲ 273.0 58.09 81.66 88.90 270.383 12.7 18.11 275.4 12.7 57.14 4 75.90～97.80 = 2 \* GB3 ② 11-3/4-Ⅰ 298.4 59.79 81.66 88.90 295.889 12.7 18.01 300.8 12.7 60.32 3-1/2 62.50～89.30 = 1 \* GB3 ① 11-3/4-Ⅱ 298.4 58.09 81.66 88.90 295.783 12.7 18.11 300.8 12.7 57.14 4 89.30 = 2 \* GB3 ② 13-3/8-Ⅰ 339.7 59.79 81.66 88.90 337.164 12.7 18.01 342.1 12.7 60.32 3-1/2 71.40～107.02 = 1