单片机蜂鸣器播放音乐代码(生日快乐 两只蝴蝶 祝你平安).doc

/*生日快乐歌曲*/ #include reg51.h #define uint unsigned int #define uchar unsigned char sbit beep = P1^5; uchar code SONG_TONE[]={212,212,190,212,159,169,212,212,190,212,142,159, 212,212,106,126,159,169,190,119,119,126,159,142,159,0}; uchar code SONG_LONG[]={9,3,12,12,12,24,9,3,12,12,12,24, 9,3,12,12,12,12,12,9,3,12,12,12,24,0}; //延时 void DelayMS(uint x) { uchar t; while(x--) for(t=0;t120;t++); } void PlayMusic() { uint i=0,j,k; while(SONG_LONG[i]!=0||SONG_TONE[i]!=0) { //播放各个音符，SONG_LONG 为拍子长度 for(j=0;jSONG_LONG[i]*20;j++) { beep=~beep; //SONG_TONE 延时表决定了每个音符的频率 for(k=0;kSONG_TONE[i]/3;k++); } DelayMS(10); i++; } } void main() { beep=0; while(1) { PlayMusic(); //播放生日快乐 DelayMS(500); //播放完后暂停一段时间 } } 两只蝴蝶： #include reg51.h // 这是 单片机音乐代码生成器 生成的代码 #define uchar unsigned char sbit beepIO=P1^5; // 输出 为 P1.5 可以修改 成 其它 IO 口 uchar m,n; uchar code T[49][2]={{0,0}, {0xF8,0x8B},{0xF8,0xF2},{0xF9,0x5B},{0xF9,0xB7},{0xFA,0x14},{0xFA,0x66},{0xFA,0xB9},{0xFB,0x03},{0xFB,0x4A},{0xFB,0x8F},{0xFB,0xCF},{0xFC,0x0B}, {0xFC,0x43},{0xFC,0x78},{0xFC,0xAB},{0xFC,0xDB},{0xFD,0x08},{0xFD,0x33},{0xFD,0x5B},{0xFD,0x81},{0xFD,0xA5},{0xFD,0xC7},{0xFD,0xE7},{0xFE,0x05}, {0xFE,0x21},{0xFE,0x3C},{0xFE,0x55},{0xFE,0x6D},{0xFE,0x84},{0xFE,0x99},{0xFE,0xAD},{0xFE,0xC0},{0xFE,0x02},{0xFE,0xE3},{0xFE,0xF3},{0xFF,0x02}, {0xFF,0x10},{0xFF,0x1D},{0xFF,0x2A},{0xFF,0x36},{0xFF,0x42},{0xFF,0x4C},{0xFF,0x56},{0xFF,0x60},{0xFF,0x69},{0xFF,0x71},{0xFF,0x79},{0xFF,0x81} }; uchar code music[][2]={{0,4}, {23,4},{21,4},{23,16},{23,4},{21,4},{23,4},{21,4},{19,16},{16,4},{19,4},{21,8},{21,4},{23,4},{21,4},{19,4},{16,4},{19,4},{14,24}, {23,4},{21,4},{23,16},{23,4},{21,4},{23,4},{21,4},{19,24},{16,4},{19,4},{21,8},{21,4},{23,4},{21,4},{19,4},{16,4},{19,4},{21,24}, {23,4},{21,4},{23,16},{23,4},{21,4},{23,4},{21,4},{19,16},{16,4},{19,4},{21,8},{21,4},{23,4},{21,4},{19,4},{16,4},{19,4},{14,24}, {23,4},{26,4},{26,16},{26,4},{28,4},{26,4},{23,24},{21,4},{23,4},{21,8},{21,4},{2