COMMANDER变频器简单使用作业指导书.doc

XXXX纸业集团股份有限公司 铜版纸工厂动力车间 名称 COMMANDER变频器简单使用作业指导书 修订时间 2008－10－15 版本 01 编号 TBZWC19 页数 3 适用范围 传动完成专业 一、需用工具： 平口小螺丝刀 二、具体内容： 1 COMMANDER 变频器主要用在令包机退纸架，竖纸板，退纸皮带，包装纸进给，矫正皮带，标签输送带，换盘区等处控制；使用和SIENENS变频器基本相类似 2 操作面板介绍及修改参数 A.上面有M和上下▲按钮用于修改参数；启动，停止，改变转向3个控制按钮用于启动操作；及一个小显示屏，用于显示各种状态 B. M按钮用于修改参数，如果被按下并且在2秒內松开，则由状态显示变为参数修改状态，上下▲按钮用于选者参数号和加减参数值 C 示例：按一下M，显示屏上显示0.XX数值出现，按上下▲按钮，显示屏上的0.XX数值会增大或减小直到即将修改的参数号松开，再按M按钮，显示屏上的参数值会闪动，然后按住上下▲按钮改变参数值直到所需时松开，再按M按钮后参数修改完成，如果修改别的参数则重复上述操作 3 具体参数 0.01 Minium speed = 0 0.02 Maxium speed =? 0.03 Acceleration rate =? 0.04 Deceleration rate =? 0.05 Reference seleration =3 0.06 Current limit = 150 0.07 Speed control P gain=200 0.08 Speed control I gain=100 0.09 Speed control D gain=? 0.10 Motor speed=0 0.11 Pre-ramp reference =0 0.12 Post-ramp reference=0 0.13 Motor active current=? 0.14 JOG reference =50 0.15 Ramp mode selector =FAST 0.16 Stop mode selector = RP 0.17 Torque mode select =0 0.18 S-ramp enable =Bit0 0.19 S-ramp da/dt limit =1.5 0.20 Skip frequency /speed1 =0 0.21 Skip band1 =5 0.22 Skip frequency/speed2 =0 0.23 Skip band2 =0 0.24 Analog input1 mode selector = LOLT 0.25 Analog input2 mode selector = LOLT 0.26 Analog input2 destination =1.37 0.27 Sequencing mode selector =Bit1 0.28 Frequency/speed demand =150 0.29 Terminal-29 destination = 2000 0.30 Forward/reverse key enable =Bit0 0.31 Macro number =0 0.32 Serial comms mode =Ansl4 0.33 Drive rated current(FLC) =? 0.34 User security code =149 0.35 Keypad reference=? 0.36 Serial comms band rate =4800 0.37 Serial comms address =1.1 0.38 Initial parameter displayed =0.1 0.39 Synchronise to a spinning motor =Bit1 0.40 Autotune =Bit0 0.41 PWM switching frequency =6 0.42 Motor-no of pole =4 pole 0.43 Motor-rated power factor =? 0.44 Motor-rated voltage =400V 0.45 Motor-rated speed =? 0.46 Motor-rated current =? 0.47 Motor-rated frequency =50 0.48 Drive operating mode selector =CL.LECT 0.49 Security status =1 0.50 Software version number =3.01 注释：上述种写出数值的为基本上不用改动的，问号的则根据不