OTISSKY1电梯故障代码大全及主板指示灯及开关说明.docxVIP

PAGE PAGE # / 18 OTIS SKY 电梯故障代码 闪烁的信息 可能的原因 TCI - Lock 轿顶检修开关操作顺序不准确，必须按以下顺序操作 1.打开厅门? 2.轿顶检修开关由检修打到正常状况 3关闭 厅门 如果不按照上面的顺序操作，电梯将不能正常运行，同时 LCBII板上的INS指示灯将会闪烁。 LS - Fault :a）上强迫减速2LS和下强迫减速1LS信号不正常 start DCS! a） 在没有完成门检查启动（DCS）操作之前正常运行不允许. b） 正常操作时，当电梯停在门区且轿厢门完全打开（DOL有 效）时，厅门门全闭信号被触发（DW有效）.此时小心检查井道 厅门门锁是否被短路? 按 M - 1 - 3 - 5 启动 DCS ! 1LS + 2LSon 限位开关1LS和2LS同时动作. DBP-Fault 电梯运行必须按正确的顺序完成. 当电梯减速停车时门区信号没有被检测 ，这个原因可能是 LVC继电器故障. 这个错误事件被存储在 LCBII EEPROM上,只能使用检修 INS开关来进行电梯操作? DBSS-Fault :变频器没有准备? Adr.- Check 特殊远程站地址没有对应于标准IO列表 TCI ( 691 ) = 16 - 3, 1LS ( 692 ) = 16 - 1, 2LS ( 693 ) = 16 - 2, SE - Fault 电梯因丢失 SE信号不能启动（检查SKL, THB, door bypass,保险丝, ） 闪烁的信息英文说明 Blinking Event Messages The following messages sre blinking in ejhch status display of ttie Service Tool: Blink- Description related setup wrongBoord The software cannoT identify ttie board 9 rsolace ttie TCBC. wroitQ E2P Tie EE FROM has not the correct size MHO active The SFB reqiiests to ignore The inputs at Manual F?escue Run. Learn Run a) The drive package is perfomninq its Learn Run to leam Ihe hoish^ay situation tD The drive package is adjusting the encoder - Aait until the team run hjs completed DRV^TYF^O DoorBridge DW or DFC input has not been lav/ while Uie door was evened. Reason is ◎ bncige-cf Qaor loch - check safety chain - This even? is stprecS into EEFROM so ttiat the ONLY y to i^ring The els1*- ator into operation ag^in is by using IlMS. Switch HNS Landing door v?a opered for longer than 斗 seconcis or ：ltm 匚日-dcn：R im I - ■ dz:^d. i^l r i ? csl- e-_ ■:■.!： ic e - This event is stored into EEPROM so that tKe ONLY wa/ to bring the elevator Into operation n is by using IMS. TCI-IOCK Tne sequence To lea^e T ci-mcode was not 匚orrectly followed i . opon docr switch TCI off close dooi TUM TDM One or the triqaer nx^duls rup or down) RSL in puts c*9t?ct€l a failure for r?1uc9d - check e-vesnt logi / switch to ERO to reset (lifter so?”lng)- l-WY-TYK io s 1O4T - 1051 1I S^-2LS oil Limit swiftches 1LS and 2LS