市政道路防沉降球墨铸铁检查井盖安装方法.docVIP

市政道路防沉降球墨铸铁检查井盖安装方法 防沉降球墨铸铁检查井盖安装方法 自调式-防沉降窨井盖框安装工法在解决窨井路框差作业中使用， 通过调换窨井盖框，旨在攻克窨井下沉后， 产生道路路框差的病害， 提高道路的平整度， 改善行车条件。 特点: 减去窨井砖墙立面80%的受力压强; 将窨井盖框与路面形成一个整体， 改变了窨井下沉而引起的窨井盖同步下沉的状况; 作业面小， 对交通影响小， 施工快捷方便，施工完成即可通车。 适用范围: 城市道路上部分公用事业管线井; 雨、 污水窨井的改造。城市道路上符合条件的公用事业管线井， 以及雨污水窨井的新建、 改建以及维修推荐采用此二种工法。 检查井盖、井圈的生产、质量、检验等均应按国家 GB/T 23858—2009检查井盖标准执行。所有井圈井盖应采用防盗、减震、减噪技术。 公司产品从原料检验、制芯、熔炼、造型、加工成型、后处理、承载试验等整个工艺流程有严格的控制程序，自动化程度高，产品质量稳定。 产品的各项技术指标完全符合本技术要求的要求，并提供铸件金相、机械性能检测报告复印件。 本公司研发圆形密封井盖技术要求:承重面钢板厚度10mm,表面清晰注明“热”字样，内侧井型加强梁钢板厚度10mm，与底座单面合叶连接开关大于90度,承重面(带挡土圈)与密封面开关简易无卡涩。底座结合面车槽加耐温胶圈分别与承重面、密封面结合。密封面采用玻璃钢防腐材料，用不锈钢元宝螺栓拉紧。底座高度200mm立面钢板厚度20mm，底座与承重面平齐吻合。整体材质为Q235-AF平整光滑加工误差小于1mm，关闭后灌水试验无渗漏。抛光除锈后刷防绣底漆外涂沥青漆。 参考标准 n the main terminal, and the telephone Office is responsible for providing the appropriate size adapter patch panels and electrical protection unit. (Shuttle bus) wiring (IDF) set up in the workshop on the second floor of the building, located in the District of weak electrical cabinets (well). Engine room placed inside the Cabinet, IDF placed a standard 40U cabinets for installation of network and wiring devices, management computer and telephone information. Cabinet distribution frame are made of Super five RJ45 patch panel horizontal twisted pair connections. Computer information management, admin area using the jumpers, which uses private RJ45-RJ45 soft jumpers for network devices with jumpers hopping between all switches, changes, expansion and maintenance were done quickly in the wiring closet. Twisted length Centre room is located on the second floor, outward radiation of each line (except some points may exceed) does not exceed 100 metres in length, all information for the various floors all rooms (distribution Cabinet) unified management. District workshop building distribution lines (IDF) via fiber optic cables connected to the total room cabinets. Fiber length were: workshops two IDF: total more than 1200 square meters, double the number of strands can be calculate