毕业设计（论文）-摩托车后灯罩注塑模具设计-抽芯【全套图纸】.docVIP

全套图纸，加695132052 毕业设计（论文） 说明书 题目名称： 摩托车后灯罩注塑模具设计 摘 要 本文详细地阐述了盖注射模具的设计过程。设计了注射模具中的各个系统，如浇注系统、导向与定位机构、侧向分型与抽芯机构，并对塑料材料性能进行了分析。根据塑件的产品数量要求，以及结构要求，该模具采用一模一腔。整个设计过程都是用CAD软件进行参数化设计，使整个模具设计过程简单明了。利用MPA软件进行模流分析，为模具设计和成型工艺的指定提供参照依据。使用CAD软件设计成型零件以及非标零件，从而进行全方面的参数化设计，即对模具进行分模、生成元件、装配、试模、开模等设计。调用标准模架以及标准件，从而完成模具的整体设计。直接指导生产。针对塑件的特点，本模具设计了侧抽芯滑块机构，也构成了本次模具设计的主要内容。 关键词 ：注射模，参数化设计，侧抽芯和滑块，灯罩 Abstract This paper describes in detail the design process of injection molding cover. Injection mold design various systems, such as pouring system, orientation and positioning mechanism, side parting and core pulling mechanism, and plastic material properties were analyzed. The number of products under the requirements of plastic parts, and structural requirements of one module and one adopted in the mold cavity. The entire design process is carried out using CAD software, parametric design, the entire mold design process simple and straightforward. MPA software using mold flow analysis, mold design and molding technology to provide reference for the specified. Molded parts using CAD software design and non-standard parts, which were all aspects of design parameters, namely, the parting of the mold to produce components, assembly, test mode, open mode, such as design. Call the standard mold base and standard parts, thus completing the overall design of the mold. Direct the production. Characteristics of plastic parts for the die design of the side core pulling slider mechanism, but also constitute the main contents of the mold design time. Keywords: injection mold, parametric design, the side core pulling and slide, shade.  目录 1 前言 - 3 - 1.1模具行业发展的现状 - 3 - 1.2我国模具发展的现状 - 3 - 1.3参数化技术慨述 - 4 - 1.4 选题目的以及意义 - 5 - 2 塑件成型工艺性分析 - 6 - 2.1摩托车尾灯罩二维图 - 6 - 2.2结构特征分析及成型工艺性分析 - 6 - 2.2.1结构特征分析 - 6 - 2.2.2成型工艺性分析 - 6 - 2.2.3 塑件材料的基本性能 - 7 - 2.2.4 塑料的成型收缩率 - 7 - 2.2.5 塑件材料的流动性 - 7 - 3 塑件成形工艺与设备 - 8 - 3.1注塑成型工艺条件 - 8 - 3.1.1 温度 - 8 - 3.1.2 压力 - 8 - 3.1.3 时间 - 8 - 3.2 注射机型号的确定 - 9 - 3.2.1 由公称注射量