9ipc-a-610d电子产品外观检验标准介绍与应用.pptVIP

Course Introduction 课程介绍 目的 提供了关于电子组装件的外观质量可接收标准的基础知识。 学员理解产品要求 （1）提高辨别技能 （2）提升灵活性，应变能力，获得最佳的制造实 （3）提供便携的职业技能 培训时间：大约3小时 参考文件 IPC-A-610D 电子组件的可接受性 IPC-T-50G 电子电路互连与封装术语及定义 IPC-A-610D Introduction IPC-A-610D介绍 IPC-A-610D Introduction IPC-A-610D介绍 IPC-A-610D Introduction IPC-A-610D介绍 IPC-A-610D Introduction IPC-A-610D介绍 IPC-A-610D Introduction IPC-A-610D介绍 Course Content 课程内容 Handling Electronic Assemblies 电子组件的操作 Handling Electronic Assemblies 电子组件的操作 Handling Electronic Assemblies 电子组件的操作 Handling Electronic Assemblies 电子组件的操作 SMT Defects Samples SMT 缺陷图例 SMT Defects Samples SMT缺陷图例 No solder 无锡 Excess Solder多锡 Solder Short Bridge短路/锡桥 Insufficient Solder 少锡 Blowholes Pinholes 锡洞 Solder Ball Splash锡珠溅锡 Icicles 锡尖 Cold Solder 冷焊 Component Tilting 零件歪斜 Epoxy on Pad焊盘有红胶 Component Lifted元件翘高 Tombstone立件 Component Damage坏件 Misalignment偏位 Fracture Solder 裂缝 Others Defects 其它缺陷 Acceptability of Solder Joint 可接受的焊点 Acceptability of Solder Joint 可接受的焊点 Acceptability of Solder Joint 可接受的焊点 Acceptability of Solder Joint 可接受的焊点 Acceptability of Solder Joint 可接受的焊点 Acceptability of Solder Joint 可接受的焊点 Acceptability of Solder Joint 可接受的焊点 Acceptability of Solder Joint 可接受的焊点 Thanks for your participating! a.Long lead / short lead 脚长/脚短b. Missing component 元件丢失c. Expose copper 露铜d. Surface scratched 外观划伤 Acceptable - Class 1,2End joint width (C) is minimum 50% of component termination width (W) or 50% land width (P), whichever is less. 元件端子连接处C的宽度至少是元件端子宽度W的50%(焊盘宽度P) Acceptable - Class 1,2A properly wetted fillet is evident. Acceptable - Class 1,2,3Properly wetted fillet evident. Target - Class 1,2,3End joint width is equal to or greater than lead width. Acceptable - Class 1,2Minimum end joint width (C) is 50% lead width (W). 元件端子连接处C的宽度至少是元件脚宽度W的50% Target - Class 1,2,3End joint width (C)is equal to or greater than lead width (W). Acceptable - Class 1,2Minimum end joint width (C) is 50% lead width (W). 元件端子连接处C的宽度至少是元件脚宽度W的50% Target - Class