芯轴托架冲压模具的设计（全套图纸）.docVIP

摘 要：本设计为芯轴托架冲压模具设计，根据零件的形状、尺寸、精度、材料等条件，首先对芯轴托架的工艺性进行了分析，并通过综合对比确定了冲压工艺方案及模具结构方案，然后通过工艺设计计算确定排样方案、计算冲压力和压力中心、初选压力机，重点对落料冲孔复合模的各组成零部件的结构、尺寸等进行设计计算，而模架则采用标准模架，再进行孔加工即可。本设计还对弯曲模及最终冲孔模的整体方案作以说明，所设计的模具结构简单、操作方便、定位基准一致、能满足产品的质量要求。最终完成四套模具之总装图、落料冲孔复合模之各零件图以及本篇论文之撰写。 关键词：模具设计、凸模、凹模、凸凹模。 全套图纸，加648328618 Abstract：This design is called the die design of the bracket of shaft．According to the shape，size，precision and material of the bracket of shaft，the forming technologies are analyzed．Through comprehensive comparing，the stamping technology and the structure of the die are determined．After the calculation of the process，the nesting board is decided．The pressure and the pressure center are calculated，the press machine is chosen initially．The design calculations for the structure and the sizes of the components which consist of the blanking and punching die are emphasized．As for the die set are chosen from the standard，only need to make some hole in them．The overall solution of the bending die and the finally punching die are also described in this design．It is proved that the structure is simple and easy to operate，it can meet the requirement of the accuracy and quality of the product．And eventually，the assembly drawing of the four set of die，the drawing of the components which consist of the blanking and punching die，as well as the writing of this paper are finished． Key words：die design、male die、female die、punch die． 目录 1. 绪 论 1 1．1冲压的概念、特点及应用 1 1．2冲压的基本工序及模具 2 1．3冲压技术的现状及发展方向 3 1．3．1冲压成形理论及冲压工艺 3 1．3．2模具先进制造工艺及设备 4 1．3．3模具CAD /CAM 5 1．3．4模具标准化 6 2．零件工艺分析 8 2．1零件的结构分析 8 2．2零件的精度 9 2．3冲压方案分析 9 3．落料冲孔复合模 11 3．1．模具类型 11 3．2操作与定位方式 11 3．3卸料与出件方式 11 3．4模架类型及精度 11 3．5工艺设计计算 12 3．5．1零件展开尺寸计算 12 3．5．2排样设计与计算 12 3．5．3冲裁力和压力中心 13 3．6凸、凹模刃口尺寸计算 15 3．6．1冲裁间隙的确定 15 3．6．2凸、凹模刃口尺寸计算 16 3．7复合模零部件设计 19 3．7．1冲孔凸模 19 3．7．2落料凹模 20 3．7．3凸凹模设计 21 3．7．4定位零件设计 22 3．7．5卸料部件的设计 23 3．7．6推件装置的设计 25 3．7．7模架及组成零件设计 27 3．7．8连接与固定零件 30 3．8模具总装图 32 3．9冲压设备的选择 34 3．10装配技术要求 34 4.弯曲模模具体设计 35 4．1弯曲模结构设计应注意的问