工程毕业设计（论文）-鸡西矿业集团张新煤矿0.9Mta新井设计（含全套CAD图）.doc

需全套CAD或三维图 联系QQ 695132052 摘 要 本设计矿井为鸡西矿业集团张新煤矿0.9Mt/a新矿井设计，一共有3层可采煤层，分别为8#、6B、2#， 煤层总厚度为4.2米。煤层工业牌号为1/3焦煤，全区走向长5900M，宽2150M,面积为12.685平方KM。设计井田的可采储量68.644Mt，设计服务年限为51年。 本矿井设计采用双立井开拓，划分为两个水平，六个采区。每个采区为单翼开采，两个工作面达产，两个工作面准备，达产时采区个数为两个，煤层全部单独开采，大巷运输采用10吨架线式电机车牵引，3吨底卸式矿车运输，区段运输平巷采用带式输送机运输，工作面采用刮板运输机运输。采煤方法为走向长壁采煤法，采煤工艺为普通机械化采煤工艺。工作面采用单体液压支柱和铰接顶梁支护，顶板处理方法为全部跨落法。年工作日330天，每日净提升16小时。 关键词：矿井设计 立井开拓 走向长壁采煤法 Abstract The design is about a 0.9MT/a new mine design to zhangxin mine in the JiXi Mining Group. there are three layers coal seam in total, 8#, 6B, 2# respectively, the total thickness of the seam is 4.2 meters. the industry of the coal is 1/3 coke, the long of region toward is 5900M, the wide is 2150 M, the area is 12.685 square KM. Mine design recoverable reserves of 68.644 Mt, design service life of 51 years. This mine design used the double-shaft development, divided into two levels, six mining area. Used the single-wing exploitation every mining area, the two face up to the middle, two face ready, there are two Mining Areas when production, all seams are individual mining, roadway transport used 10 tons of F-Line traction motor vehicles, three tons dump cars transport, Section transport belt conveyors used in horizontal transport, Face scraper transport planes. Mining method for long-wall mining, the mining technology to ordinary mechanized mining technique. Working face hydraulic prop and hinged beam supporting the roof all the way to handle cross-loading method. Working days, 330 days, the daily net up grade 16 hours. Key words: mine design shaft pioneering long-wall mining merhod  目 录 摘 要 I Abstract II 绪 论 1 第1章 井田概况及地质特征 2 1.1 井田概况 2 1.1.1 井田位置及范围 2 1.1.2 交通位置 2 1.1.3 地形、地势 3 1.1.4 气象、地震 3 1.1.5 河流 3 1.1.6 原材料及水电供给情况 3 1.2 地质特征 3 1.2.1 矿区范围内的地层情况 3 1.2.2 井田范围内和附近的主要地质构造 7 1.2.3 煤层赋存状况及可采煤层特征 10 1.2.4 岩石性质、厚度特征 12 1.2.5 井田内水文地质情况 12 1.2.6 沼气、煤尘及煤的自燃性 12 1.2.7 煤质、牌号及用途 13 第2章 井田境界、储量及服务年限 14 2.1 井田境界 14 2.1.1 井田周边情况 14 2.1.2 井田境界确定的依据 14 2.1.3 井田