白莲岩公路设计及施工组织设计.docVIP

摘 要 设计为我国皖南山区的白莲岩公路设计，白莲岩地区隶属安徽省六安市，此地区地形属于山岭重丘。路段全长2802m，拟为山岭重丘区的二级公路，共设有3个平曲线，在所有圆曲线处均设缓和曲线。第一个弯道设有缓和曲线，缓和曲线长度60米，圆曲线半径500米。第二个弯道也设有缓和曲线，长度为80米，圆曲线半径450米。第三个弯道半径为150米，设缓和曲线，长度为50米。根据规范，第一和第二个圆曲线只设超高，第三个曲线设有超高和加宽。整个路段共设有一个竖曲线，坡度分别为0.77%和3.34%，半径设为5000米。路拱采用双向坡面，坡度值采用2%。路段路面设定两种方案，分别为沥青路面以及水泥混凝土路面。 关键字：一级公路 平原地区 沥青路面 水泥混凝土路面 ABSTRACT My design is the design for highway of BAILIANYAN of the south mountain area of Anhui in our country, BAILIANYAN area is in liuan city, Anhui Province , this regional topography is the hills. The total length of the highway is 2802m , it was designed by the 3rd road in hill area, there are 3 curves altogether, have ease curves in all curve places . The first curved way relaxes the ease curve, the length is 60 meters, the radius of curve is 500 meters. The second curved way relaxes the ease curve too, the length is 80 meters, the radius of curve is 450 meters. Third curved dishes of radius 150, is it ease curve to set up, length 50. According to the norm, the first and second curve only has the hyperlenth, the third curve has hyperlenth and widens. There is a vertical curve altogether in the whole highway section , the slope is 0.77% and 3.34% respectively, the radius is set as 5000 meters. The way is joined and adopted two-wayly and domatically, slope value adopts 2%. The highway section road surface establishes two kinds of schemes, one is the asphalt road surface and another is cement concrete road surface. Key word: the 2rd highway; hills; asphalt surface; concrete surface 目 录 第一章 总说明书 1 1.1地理位置图 1 1.2 说明书 1 1.2.1设计任务、路线起讫点、中间控制点、全长及工程概况 1 1.2.2 沿线地形、地质、地震、水文等自然地理特征及其与公路建设的关系 1 1.3 与周围环境和自然景观相协调的情况 1 第二章 路线设计 3 2.1公路等级的确定 3 2.2技术标准与技术标准的总体运用情况 3 2.3路线方案 4 2.3.1路线拟定的基本原则 4 2.3.2路线走向 4 2.3.3设计范围 4 第三章 路线平面设计 5 3.1 导线要素计算及导线绘制 5 3.1.1 交点间距计算 5 3.1.2导线方位角计算 5 3.1.3导线间偏角计算 6 3.1.4曲线要素计算 6 第四章 路线纵断面设计 11 4.1纵断面设计 11 4.1.1纵坡设计原则[3] [4] [5] [6] [7] 11 4.1.2平纵组合的设计原则[