比亚迪F3R手动变速器设计（含全套CAD图纸）.doc

买文档后送图纸，QQ 194535455 摘 要 本文设计研究了三轴式五挡手动变速器。首先，对于变速器的工作原理做了阐述，从传动机构到倒档布置方案都一一做了详细的说明，完成了换挡机构形式和轴承的选择等，特别值得一提的是在倒档的选择和布置上。因为变速箱在低档工作时作用有较大的力，所以一般变速箱的低档都布置靠近轴的后支承处。 紧接着对变速器的各挡齿轮和轴做了详细的设计计算，包括了档数、传动比、中心距以及各档齿轮的齿数，并且进行了强度校核，紧接着对一些标准件进行了选型，其中包括同步器、操纵机构、固定件以及密封件等等。 最后进行的是齿轮、轴以及轴承的校核，其中齿轮校核包括弯曲强度和接触应力，轴校核包括强度和刚度的计算，轴承校核的则是其寿命计算，并讲述了变速器中各部件材料的选择。 关键字：变速器；设计；齿轮；轴；校核 ABSTRACT This design of a three-axis five-speed manual transmission. First, the working principle of transmission are described in detail, from the transmission to reverse layout programs are all doing a detailed description, complete the form and bearing of shift the choice of institutions and so on, is particularly worth mentioning is the reverse of the on the selection and arrangement. Because the role of transmission in low-grade work, a greater force, it is generally low-grade gearbox are arranged near the support at the rear axle.  Then each block of the transmission gears and shafts made a detailed design calculations, including the gears, transmission ratio, center distance and the number of teeth of the gear profile and strength check carried out, followed by a number of standard parts were selected type, including synchronization, control mechanism, fixed fittings and seals and so on.  Finally, the gear, shaft and bearing checking, checking gear which includes bending strength and contact stress, axial strength and rigidity checking, including the calculation of the bearing checking is its life span, and about each transmission component materials of choice.  . Keywords : Transmission; Design; Gear; Axis;Checking  目 录 摘 要 I ABSTRACT II 第1章 绪 论 1 1.1选题的背景 1 1.2 设计目的及意义 2 1.3 国内外研究现状 2 1.3.1 国内研究现状 2 1.3.2 国外研究现状 3 1.4 设计主要内容 3 第 2 章 变速器总体方案设计 5 2.1 设计初始数据 5 2.2 变速器设计应满足的基本要求 5 2.3 传动机构布置方案分析 6 2.3.1两轴式变速器和中间轴式变速器的特点分析 6 2.3.2 倒挡布置方案 6 2.3.3 其他问题 7 2.4各档齿轮位置安排 7 2.5变速器齿轮形式与自动脱档分析 8 2.5.1齿轮形式 8 2.5.2变速器自动脱档分析 9 2.6换挡机构形式 9 2.7本章小结 10 第3章 变速器主要参数设计 12 3.1 挡数的选择和确定 12 3.2 各档传动比的确定 12 3