采矿工程毕业设计（论文）-鹤岗矿业集团南山矿1.5Mta新井设计【全套图纸】.doc

摘 要 本设计矿井为鹤岗矿业集团南山矿1.5Mt/a新井设计，共有3层可采煤层，可采煤层厚度从上到下依次为9.2m、3.3m、15m，煤层的平均倾角为26.6°，煤层的工业牌号为1/3焦煤。设计井田工业储量228.17Mt，可采储量152.873Mt，服务年限72.8a。 本设计矿井采用双立井开拓方式，井筒位置选择在井田储量中心的西部，划分两个开采水平。大巷布置方式采用集中大巷布置，大巷运输方式采用8t蓄电池电机车牵引3.0t固定矿车运输。采煤方法为走向长壁采煤法，采煤工艺为综合机械化放顶煤开采，采空区处理方法为全部垮落法。 主井采用一对12t箕斗提升，副井采用一对三吨双层单车罐笼不平衡提升。 矿井通风方式为两翼抽出式，其中北翼风井选择在北一、北二两个采区的上山之间，南翼风井选择在南一、南二两个采区的上山之间。 矿井的排水方式为分区式排水，其中北一、南一采区使用一个排水系统，北二、南二采区分别使用一个排水系统。 关键词：双立井；集中大巷；走向长壁；放顶煤开采 全套图纸，加153893706 Abstract This is a new design of 1.5Mt/a for NANSHAN mine of HEGANG coal mining Group, which has three workable coal seams. Thickness of coal seam is 9.2m, 3.3m, 15m from top to bottom. Slope angle of coal seam is 26.6?s industry card of which is 1/3 coking coal. Industry quantity of the mining filed is 228.17 Mt, and the workable reserves is 152.873 Mt, service life is 72.8a. The mine design uses the double vertical shaft development. Shaft position is selected in the west of the storage center. The mine is divided into 2 levels, dopting concentrated main lane decoration; the main lane adopts 10t haulage motor to lead the 3.0t fix car. Coal mining method is strike longwall working, and conventional machinery breaking mining. The roof is caving method roof control. The hoist uses the 12t multiropes to lift. The chippy hoist is a pair of 3t double layer cage. Mine ventilation is double-vane drawing out types.The north air shaft is established between two distract raise of north NO.1 and NO.2, and the south is between south NO.1 and NO.2. Draining method is zone patterns. The north NO.1 and south NO.1 use one draining system, and the north NO.2 and south NO.2 use two draining systems. Key words: Double Vertical Shaft; Concentrated Main Lane; StrikeLongwall Working; Breaking Mining 目 录 摘 要 I Abstract II 绪论 VII 第1章 井田概况及地质特征 1 1.1 井田概况 1 1.1.1 交通位置 1 1.1.2 地形地势 1 1.1.3 气象和地震 2 1.1.4 井田区及邻区生产建设及规划情况 2 1.1.5 矿区经济状况 2 1.2 地质特征 2 1.2.1 矿区范围内的地层情况 2 1.2.2 井田范围内和附近的主要地质构造 3 1.2.3 煤层赋存状况及可采煤层特征 4 1.2.4 岩石性质 厚度特征 4 1.2.5 水文地质情况