TAD720VE Engine training.ppt

缸序号 燃油系统 油门控制杆 4 3 2 1 X Y 油门控制杆位移 1、满负荷+过度起动油门（Y) 2、停机位置 3、压力弹簧 4、油门控制杆 - Heinzmann + - 扭矩控制 (发电机组不适用) 手动停油杆 调速器弹 簧和飞锤 速度降调整 调速器后座调整 限制高怠速 的的安全螺钉 最高怠速调整 最低怠速调整 最大起动油门 最大燃油限制 排烟限制器r (发电机组不适用) 12. 控制杆 3. 油门拉杆 4. 压力弹簧 调速器 调速器外观- Heinzmann 1 2 3 4 5 6 7 8 1. 速降调节 2. 调速器驱动齿轮 3. 停机杆 4. 3针接头,为额外的燃油起动电磁阀 (不适用于发电机组用发动机) 5. 连接到冒烟限制器的增压压力管 (不适用于发电机组用发动机) 6.额外的燃油起动电磁阀 (不适用于发电机组用发动机) 7. 高怠速调节 8. 低怠速调节9. 油门杆 9 冷却系统- T(A)D 520 / 720 GE/VE 从散热器来的冷却水 节温器座 冷却水循环泵 机油冷却器 冷却缸套 冷却缸头 到散热器的冷却水 冷却系统 - T(A)D 520 / 720 GE/VE 1 2 3 4 4 3 2 1 从冷却水箱到发动机冷水 从发动机到冷却水箱热水 从发动机到膨胀水箱排气管 从膨胀水箱到水泵静态压力管 P P ? 水位传感器 机体 (= 接地) RPM 充电 灯. 水温 水温报警灯 油压. 油压报警灯 冷却水位报警灯 主开关 发火 / 停机 起动 停机电磁阀 24V/1.6A 12V/3A G M NTC -30 ? +140?C +113?C NO G W G 0 - 6 bar 2 bar NO NO S D+ W B+ 30 50 - + 推荐电路图 TAD 5/7 ENGINE NAME PLATEThe engine name plate is mounted on the right hand side of the engine.The engine serial number is also stamped into the engine block on the right hand side of the engine near by the timing gear casing. BLOCK-TYPE CYLINDER HEADThe cylinder head is made of grey cast iron and designed as a one piececylinder head. The combustion air enters vertically and the exhausts aredischarged laterally. The inlet and outlet are located on the same side ofthe cylinder head.VALVES, VALVE GUIDES AND VALVE SEATSThe engines are provided with one inlet and one exhaust valve per cylinder. The valve guides are different in production compared to the spare part.To simplify the installation of the spare part, the valve guide is equipped with a collar. The valve guide is shrunk in the cylinder head.To prevent excessive oil consumption and carbon build up, a very thin O-ringis installed at the upper end of the valve guide.Be careful when installing the valve so that the O-ring is not damaged.The valve seat inserts are made of high quality steel and are shrunk in thecylinder head. The valve seat inserts can be renewed.The seat angle for the inlet valve is 30°.The seat angle for the exhaust