旋流风口ra-n3选型计算表格.xls

英文版 中文版 m L/s/m2 L/s Min Permissible Airflow Max Diffuser Airflow Diffuser Turndown Min Diffuser C/L @ max airflow Max Diffsuer C/L @ min airflow K Min Diffuser Airflow 2 -12 K Min Diffuser Airflow 2 -15 K Min Diffuser Airflow selected dT supply-room (cooling) Permissible Turndown to Turndown too low INPUT dT used Chosen Turndown to Turndown to Min Airflow KEY Max Specific Airflow Rate Max Diffuser Airflow Rate max recommended PNC Pa Max Airflow Collar - 4-way blow Collar - 3-way blow Collar - 2-way blow 0-3w 1-3w 2-3w 3-3w 4-3w 5-3w 0-2w 1-2w 2-2w 3-2w 4-2w Enter AUTO or diffuser airflow rate Enter AUTO or specific airflow rate Max Recommended Airflow Notes: Min C/L Distance Ave C/L Distance Max C/L Distance min permissible Turndown too low Draught Stagnation Specific airflow too low Supply air too cold RA-N3-DN350 DN350 DN500 RA-N3-DN500 For distances to walls halve C/L distances. Return air openings at the same height as the diffuser should be at a distance of at least 5 x DN from the diffuser to prevent short circuiting. Max SOUND Pressure Level per Diffuser mm Spigot Diameter 30 35 Max TOTAL Pressure (incl connection box F) Max STATIC Pressure (incl connection box F) Max Sound Pressure Level per Diffuser based on 10 dB sound absorption in the room ref 10^-12 W. 45 55 65 ≤ 30 Min Permissible Turndown to Values should be ≥ -20 K and ≤ 0 K Version: 17/09/07 Distances between diffusers are based on satisfying an ADPI of at least 90% for 2.7 m discharge height. Enter AUTO or enter turndown % (eg 100% for CV) Version: 17/09/07 m3/h m3/h m3/h m3/h/m2 dT 送风温差 (供冷) 风口最大送风量 单位地板面积最大送风量 输入Auto或风口设计送风量 输入Auto或最小送风量与设计风量百分比，如定风量为100％ 输入Auto或单位地板面积送风量 最大送风温差：-20K 送风过冷 单位地板面积送风量过小 领环 - 4向出风 领环 - 3向出风 领环 - 2向出风 喉部直径 1-2w: 1号领环2向出风 5-3w: 5号领环3向出风 0-2w: 0号领环2向出风 风口最大设计风量 风口最大推荐风量 允许风量减小至 设计风量减小至 风口风量最小减小至 风量减小至 最小允许减小至 最小送风量 允许最小送风量 风口最小中心间距 风口平均中心间距 风口最大中心间距 风口最大静压损失（含静压箱） 风口最大全压损失（含静压箱） 4-3w: 4号领环3向出风 小于最小允许风量 大于最大推荐风量 减小百分比过低 小于该间距则产生吹风感 大于该间距则出现停滞点 单个风口声压级 备