CAD课程设计论文.docVIP

电子CAD课程设计要求 一、课程设计的目的 熟悉原理图的设计步骤 绘制原理图的方法 网络表及元件清单的生成 双面印制电路板（PCB）的布线流程 原理图元件库及其PCB元件库的创建 二、课程设计内容和要求 1、画原理图 2、设计双面印制电路板 3、原理图元件库及其PCB元件库的创建 三、原理图: 步骤: 1、设置图纸大小 2、设置环境 3、放置元件 4、原理图布线 5、语法检查，不断修改，直到没有错误 6、材料清单和网络表生成，为PCB做准备 四、PCB图： 步骤： 设置PCB图大小 2、设置PCB环境 完成布线 五、设计内容： 1、模拟信号数据采集电路原理图 2、模拟信号数据采集电路PCR图 3、元件清单列表 Description Designator Footprint LibRef Quantity Capacitor C1 RAD-0.3 Cap 1 Capacitor C2 RAD-0.3 Cap 1 Capacitor C3 RAD-0.3 Cap 1 Capacitor C4 RAD-0.3 Cap 1 Capacitor C5 RAD-0.3 Cap 1 Polarized Capacitor (Radial) C6 RB7.6-15 Cap Pol1 1 Jack Socket, 1/4 [6.5mm], Thru-Hole, Vertical, 2-Conductor with Tip closed J1 PIN3 Phonejack2 TN 1 Header, 8-Pin JP1 HDR1X8 Header 8 1 Resistor R1 AXIAL-0.4 Res2 1 Resistor R2 AXIAL-0.4 Res2 1 Switch S1 SPST-2 SW-PB 1 EPROM/ROM High-Speed Micro U1 SOT129-1 DS87C520-MCL 1 +5V, 1Msps, 8-Channel, 8-Bit ADCs with 1礎 Power-Down U2 SOT361-1 MAX118CPI 1 Crystal Oscillator Y1 BCY-W2/D3.1 XTAL 1 4、DCR测试 Protel Design System Design Rule Check PCB File : \Users\lishun\Desktop\李顺\模拟信号数据采集电路.PCBDOC Date : 2010/11/25 Time : 18:57:10 Processing Rule : Room李顺通信2班(Bounding Region = (1640mil, 1225mil, 3640mil, 1380mil) (InComponentClass(geqinyang)) Violation between Small Component C1(4375mil,3115mil) on Top Layer and Room李顺通信2班(Bounding Region = (1640mil, 1225mil, 3640mil, 1380mil) (InComponentClass(geqinyang)) Violation between Small Component C2(2995mil,2395mil) on Top Layer and Room李顺通信2班(Bounding Region = (1640mil, 1225mil, 3640mil, 1380mil) (InComponentClass(geqinyang)) Violation between Small Component C3(2985mil,3000mil) on Top Layer and Room李顺通信2班(Bounding Region = (1640mil, 1225mil, 3640mil, 1380mil) (InComponentClass(geqinyang)) Violation between Small Component C4(3675mil,4675mil) on Top Layer and Room李顺通信2班(Bounding Region = (1640mil, 1225mil, 3640mil, 1380mil) (InCo