- 1、本文档共7页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 5、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 6、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 7、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 8、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
IIIUT专业试题
SPECIFIC EXAMINATION FOR UT-Ⅲ
FOR ASME CODE PRODUCTS
ASME超声波Ⅲ级检测人员专业考试试题
EXAMINEE: DATE: SCORE: .
应试人: 日期: 得分:
EXAMINER: DATE: .
考评人: 日期:
In the following selecting questions, choose the letter representing the right answer into the brackets (5%each, total 100%)
对下列选择题,选择代表正确答案的字母填入括号内
1. According to the requirements of the amplitude control of the ultrasonic instrument, if an indication is set at 80% of full screen and its limit is 16~24% of full screen,then the variation of the corresponding sound pressure is( )
按超声波辐度控制要求,若回波调为80%满屏高,其范围为满屏16~24%,则相应的声压变化为:
A. -7.9 ~ -4.4dB B. +4 ~ +7.6dB
C. -14 ~ -10.5dB D. +10 ~+13dB
2. When the examination equipment shall be checked and calibrated by the use of the calibration standard?( )
A. At the beginning and end of each examination
B. When examination personnel are changed
C. At any time that malfunctioning is suspected
D. All of the above
探伤仪何时需用校正试样校验?( )
A. 每次检测开始和终了 B. 检测人员更换时
C. 怀疑仪器有故障时 D. 以上都是
3. The rate of probe movement for examination of welds shall not exceed( ), and each pass of the probe shall overlap a minimum of( )of the transducer width.
焊缝检验时探头移动速度不得大于( ),探头每次移动时应保证至少重叠( )探头宽度
A. 200mm/s B. 6in./s
C. 10% D. 20%
4. According to T-542, for the ultrasonic examination of welds, the exam-starting level is ( ), the indication-evaluating level is ( ) and the flaw-measuring level is( )
按T-542,焊缝UT的起始灵敏度为( ),评定灵敏度为( ),定量灵敏度为( )。
A. DAC B. DAC-6dB C. DAC-10dB D. DAC-14dB
5. A 20 in. diameter curved calibration block ma
您可能关注的文档
- gcc错误解决方法.doc
- GCG序列分析.pdf
- GCT英语测试词汇.doc
- GC_MS分析大蒜中的挥发油和大蒜精油.pdf
- GC/MS分析铝箔轧制基础油组成.pdf
- GDI+编程基础(一)GDI+VsGDI.doc
- Gdb的简单使用gdb+gdbserver方式进行ARM程序调试.pdf
- Gemund. Analysis of a sharedmemory multiprocessor via a novel queuing model.pdf
- General Analysis of New Physics in Bto Jpsi K.pdf
- General principles and rules for technical drawing (技术设计图形位公差总则).pdf
文档评论(0)