螺纹各国标准对照.docVIP

一、英制螺纹（螺纹牙型角55度）Thread of British standard ( Thread pitch shape angle 55°)? ? ? ? BSW－－－－英国标准惠氏螺纹（粗牙）British Standard Whitworth Thread ( Coarse )? ? ? ? BSF－－－－英国标准惠氏螺纹（细牙）British Standard Whitworth Thread ( Fine )? ? ? ? G－－－－直管螺纹（外螺纹分A、B两面级、丝锥分G、G－D）Straight pipe thread ( Outside ) ? ? ? ? ? ? ? thread in A\B: taps in G、G－D )? ? ? ? R－－－－锥管外螺纹（旧代号ZG;KG）Outside paper pipe thread ( Old thread code ZG,KG )? ? ? ? RC－－－－锥管内螺纹（旧代号ZG;KG）Inside taper pipe thread ( Old thread code ZG,KG )? ? ? ? 二、美制螺纹（螺纹牙型角60度）Thread of American standard ( Thread pitch shape angle 60°? ? ? ? UNC－－－－统一制粗牙螺纹（代替NC）Unified coarse pitch thread ( Instead of NC )? ? ? ? UNF－－－－统一制细牙螺纹（代替NF）Unified fine pitch thread ( Instead of NF )? ? ? ? UNEF－－－－统一制超细牙螺纹Unified superfine pitch thread? ? ? ? UN－－－－－统一制不变螺距螺纹Unified thread? ? ? ? UNS－－－－统一制特殊螺纹Unified Special thread? ? ? ? NPT－－－－一般用途锥管螺纹（旧代号Z;K）Taper pipe thread for general purpose ( Old ? ? ? ? ? ? ? ? thread code Z,K )? ? ? ? NPSC－－－－管接头直管内螺纹Internal straight pipe thread for connection? ? ? ? NPSM－－－－设备上自由配合，机械连接用直管螺纹Straight pipe thread for general purpose? ? ? ? NPTF－－－－干密封锥管螺纹Dryseal taper pipe thread? ? ? ? NPSF－－－－干密封燃油直管螺纹Dryseal straight pipe internal thread? ? ? ? NGT－－－－气瓶用锥螺纹Special thread for gas cylinder? ? ? ? 三、米制螺纹Metric thread? ? ? ? ZM－－－－－米制锥管螺纹 Metric taper pipe thread? ? ? 四、其它螺纹Other threads? ? ? ? SM－－－－缝纫机螺纹Thread for sewing machine? ? ? ? PZ－－－－气瓶用锥螺纹Special thread for gas cylinder? ? ? ? 5V1－20V1－气门芯螺纹5V1－20V1－Tyre valve thread? ? ? ? 螺纹代号说明示例：Explanation of thread code. e. g.? ? ? ? 1/4－20UNC? ? ? ? 1/4－公称直径1/4 nominal dia. 1/4? ? ? ? 20－每寸20牙twenty teeth per inch? ? ? ? UNC－美标统一制粗牙螺纹unified coarse pitch thread NPT为60度牙型角锥管螺纹,R为55度牙型角螺纹密封的管螺纹,R为圆柱外螺纹,RC为圆锥内螺纹,Z为标准锥管螺纹.NPT为60度牙型角锥管螺纹用螺纹密封的管螺纹其标记及各种螺纹的特征代号规定如下： Rc—圆锥内螺纹 Rp—与圆锥外螺纹配合的圆柱内螺纹 R—圆锥外螺纹 G螺纹表示非螺纹密封的管螺纹 BSP为英制管螺纹总体代号，但是分为三种BSPP、BSPT和BSPF。BSPP（British Standard Pipe Parallel (thread)）为英制圆柱管螺纹代号，只有内螺纹，相当于国内的55度圆柱(平行)管螺纹,即G，而B