- 1、本文档共59页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
钢筋调直机设计说明书硕士论文
摘要
GT1.6/4型调直切断机主要由、、牵引、切断、、等组成
Abstract
GT1.6/4 type straightening cutting machine is mainly composed of loading plate, straightening device, traction device, cutting device, cutting device, frame, etc. Is mainly used for 1.6 Φ Φ diameter 4 mm mild steel, cold rolled steel wire, stainless steel wire of the modulation.
Steel bar straightening cutting machine at the time of design need to consider to cut off the institutions and straightening mechanism scheme design. According to the requirement of the specification, the final cut off the way for the hammer to cut off the way: for medium and small diameter steel bar, work continuously, large noise. Easy appear even cutting phenomenon, length minimum error. Module as a way of straightening straightening: reinforced straightening effect is good, easy to control. But straightening speed is low and processing steel surface is slashed and working noise; Suitable for all kinds of round steel bar.
The machine in operation, ensure the wire feeding from left to right direction; Adjusting cutter after commissioning normal, there is no invalid shear phenomenon; After straightening steel to allow a slight abrade, but weight loss is not greater than 0.5%.
The straightening cutting machine in the actual production of the design is completed will meet requirements: (1) the straightening to cut off the wire diameter: 1.6 Φ Φ 4 mm; (2) the straightening cutting wire length: 100 mm - 1000 mm; (3) cutting length error: Δ L 2 mm or less; (4) steel wire straightening cutting off after the straightness error is not more than 2 mm/m. (5) the traction steel wire speed: 20-30 m/min. (6) to cut off the motor power: 2.2 kw.
Key words: reinforced; Straightening cutting machine; Invalid shear
目录
第一章 前言 1
第二章 钢筋调直机的设计 2
2.1 钢筋调直机的分类 2
2.2 钢筋调直机调直剪切原理 2
2.3 钢筋调直机的主要技术性能 3
2.4 钢筋调直机工作原理与基本构造 4
第三章 电机选择 10
3.1 生产率和功率计算 10
3.1.1 生产率计算 10
3.1.2 功率计算,选择电动机 10
第四章 皮带选择 15
4.1 第一组皮带传动机构的设计 15
4.1.1 确定设计功率 15
4.1.2 初选带的型号 15
4.1.3 确定带轮的基准直径和 15
4.1.4
您可能关注的文档
- 重庆山伦摩托车销售有限公司珞璜厂区工程施工组织设计.doc
- 重庆市助理农艺师职称考试资料.doc
- 重庆市合川区高速公路建设指挥部35kV三清线36#-38#迁改及110kV江三线63#-73#段迁改工程.doc
- 重庆市合川区旅游市场现状及营销策略(毕业论文).doc
- 重庆市巴南区防洪护岸综合整治二期工程格宾挡墙施工组织设计.doc
- 重庆市巴南安澜镇石板垭小分队三下乡策划书.doc
- 重庆市康居西城三社区人口层次调研报告.doc
- 重庆市慧达物业服务申报材料.doc
- 重庆市永川区陈食镇梓潼观等(二)个村土地整理项目新增耕地报告.doc
- 重庆市永川区港桥工业园区主干道工程施工组织设计.doc
- GB/T 39560.10-2024电子电气产品中某些物质的测定 第10部分:气相色谱-质谱法(GC-MS)测定聚合物和电子件中的多环芳烃(PAHs).pdf
- 中国国家标准 GB/T 39560.10-2024电子电气产品中某些物质的测定 第10部分:气相色谱-质谱法(GC-MS)测定聚合物和电子件中的多环芳烃(PAHs).pdf
- 《GB/T 39560.10-2024电子电气产品中某些物质的测定 第10部分:气相色谱-质谱法(GC-MS)测定聚合物和电子件中的多环芳烃(PAHs)》.pdf
- GB/T 39560.302-2024电子电气产品中某些物质的测定 第3-2部分:燃烧-离子色谱法(C-IC)筛选聚合物和电子件中的氟、氯和溴.pdf
- 中国国家标准 GB/T 39560.2-2024电子电气产品中某些物质的测定 第2部分:拆解、拆分和机械制样.pdf
- 中国国家标准 GB/T 39560.302-2024电子电气产品中某些物质的测定 第3-2部分:燃烧-离子色谱法(C-IC)筛选聚合物和电子件中的氟、氯和溴.pdf
- GB/T 39560.2-2024电子电气产品中某些物质的测定 第2部分:拆解、拆分和机械制样.pdf
- 《GB/T 39560.2-2024电子电气产品中某些物质的测定 第2部分:拆解、拆分和机械制样》.pdf
- 《GB/T 39560.303-2024电子电气产品中某些物质的测定 第3-3部分:配有热裂解/热脱附的气相色谱-质谱法(Py/TD-GC-MS)筛选聚合物中的多溴联苯、多溴二苯醚和邻苯二甲酸酯》.pdf
- 中国国家标准 GB/T 39560.303-2024电子电气产品中某些物质的测定 第3-3部分:配有热裂解/热脱附的气相色谱-质谱法(Py/TD-GC-MS)筛选聚合物中的多溴联苯、多溴二苯醚和邻苯二甲酸酯.pdf
文档评论(0)