煤矿新井设计本科生毕业（设计）论文.docVIP

摘要 本设计矿井为煤矿新井设计，设计生产能力为1.2Mt/a，服务年限62.85a。根据设计要求，井田的工业资源储量为15751.59万吨,可采储量为105.8Mt。井田走向长8km，倾斜长5km，煤层平均倾角15°，属于缓倾斜煤层。 本设计矿井采用双立井的开拓，单层大巷布置方式。共划分十一个采区，其中首采区为211采区，布置一个工作面同时生产。采煤工艺为综采，大巷采用胶带输送机运煤。年工作日为330d，采用“三八”工作制，工作面长为180m，截深0.865m，班进两刀,第三班检修。 由于井田走向较长，且为缓倾斜煤层，以及煤层地质条件等因素影响，决定本井田内全部采用走向长壁采煤法开采。 主井装备：12t箕斗，钢丝绳罐道,箕斗由四根钢丝绳提升。副井采用1.5t罐笼提升。副井采用一套为1.5t矿车单层单车双罐笼提升设备，槽钢组合罐道。 矿井通风方式为中央分列式，通风方法为抽出式。 关键词：立井；上山开采；大采高；单巷掘进；中央分列式 Abstract design of mine for XX in some mine Nii design, the design production capacity of 1.2Mt/a, length of service 62.85a. According to the design requirements, Ida industrial resources reserves 157515900 tons, recoverable reserves is 105.58Mt. Ida to long 8km, long 5km tilt, the average coal seam dip 15 °, which belongs to the gently inclined seam. The design of double shaft mine development, single lane layout. Is divided into eleven districts, one of first mining area of 211 mining area, layout of a working face production at the same time. Mining technology for fully mechanized mining, roadway using belt conveyor coal. Years working for 330D, use three eight working system, working face length is 180m, cutting depth 0.865m, class two knives, third class maintenance. Due to long Ida, and gently inclined seam, and the seam geological conditions and other factors, decided the Ida all used to long wall mining mining. Main equipment: 12t skip, wire rope guide, skip the four wire rope hoist. Auxiliary shaft cage hoisting by using 1.5T. Auxiliary shaft adopts a set of 1.5T tramcar monolayer cycling double cage lifting equipment, steel composite cans. Mine ventilation for the central parade, ventilation method for extraction type. Keywords: shaft; exploitation; large mining height; single lane tunneling; central parade \ 1 矿区概述及井田地质特征 1.1 矿区概述 1.1.1 交通位置 矿井田位于省县之西南约10 Km，井田外形为不规则菱形。其范围：西南以小煤矿（局部以9#煤层露头）和F40断层为界，西北及东北分别止于F2及F18断层，东以F22、F19、F34断层为界，东南止于F12断层南北长约8 Km，东西宽约5 Km，面积23.1Km2。 京广铁路和京深高速公路及107国道由矿区东侧通过，工业广场至车站8 Km，距站10Km，矿区运煤专用铁路在车站与线接轨，储