通信原理课设路基带的FSK信号传输系统的设计教程方案.docx

武汉理工大学《通信原理》课程设计说明书  PAGE \* MERGEFORMAT 3 课程设计任务书 学生姓名： 专业班级： 信息1203班 指导教师： 工作单位： 信息工程学院 题 目: 基本题：基于信道编码的数字基带信号传输系统 扩展题：4路基带的2FSK信号传输系统的设计 初始条件： 1路数字基带信号的传输速率为 1KHZ； 时分复用信号路数为2； 频分复用信号路数为2； 同步信号的提取方法为帧同步法。 信道衰减为 20dB，存在白噪声； 仿真软件为 SystemView。 要求完成的主要任务: （包括课程设计工作量及其技术要求，以及说明书撰写等具体要求） 1、设计复用信号的帧结构和帧同步码； 2、设计发送、传输（无ISI）、接收和同步电路（小组成员分工）； 3、确定部件类型、参数（电路放大倍数、带宽）等性能指标； 4、连接部件组成系统，调试； 5、仿真验证，要求收发信号波形基本一致并对结果进行分析； 6、说明书撰写严格执行教务处文件。 时间安排： 12.15 ～12.30 设计系统电路、仿真调试、写报告； 1.9 答辩。 指导教师签名： 年 月 日 系主任（或责任教师）签名： 年 月 日  目录 1 绪论···········································1 1.1任务要求··············································1 1.2 2FSK简述·············································1 1.3时分复用简述··········································1 1.4频分复用简述··········································1 1.5 systemview简述·······································1 2 实现方案·······································3 2.1 原理框图··············································3 2.2 总体思想··············································3 2.3 仿真系统图············································4 3 发送部分各模块设计····························5 3.1 基带/帧同步信号产生模块·······························5 3.1.1 基带/帧同步信号产生模块原理框图·························5 3.1.2 基带/帧同步信号产生模块仿真图···························5 3.1.3 基带/帧同步信号产生模块原理·····························5 3.2 提速模块··············································7 3.2.1 基带/帧同步信号产生模块原理框图·························7 3.2.2 基带/帧同步信号产生模块仿真图···························7 3.2.3 基带/帧同步信号产生模块原理·····························8 3.3 时分复用模块··········································9 3.3.1 基带/帧同步信号产生模块原理框图·························9 3.3.2 基带/帧同步信号产生模块仿真图···························9 3.3.3 基带/帧同步信号产生模块原理····························9 3.4 2fsk调制模块········································11 3.4.1 基带/帧同步信号产生模块原理框图························11 3.4.2 基带/帧同步信号产生模块仿真图··························11 3.4.3 基带/帧同