- 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
- 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
PAGE
分类号:TU976+.1 U D C:D10621-408-(2015) 1446-0
密 级:公 开 编 号:2011072017
分类号:TU976+.1 U D C:D10621-408-(2015)1446-0
密 级:公 开 编 号:2011072017
成都信息工程学院
学位论文
某小区7层住宅楼低压配电系统设计
论文作者姓名:申请学位专业:电气工程及其自动化申请学位类别:工学学士指导教师姓名(职称):论文提交日期:2014年06月10日
某小区7层住宅低压配电系统设计
摘 要
这次毕业课程设计的题目是对某小区7层住宅的低压配电系统的设计,不考虑电梯设计,每层有4户住户,每栋楼有三个单元,不考虑地下层的设计,不考虑屋顶装饰照明的设计。这次毕业课程的设计主要是对于住宅的弱电系统来进行考虑和设计的,设计的主要内容分为四点:1.依据相关规定和条例对负荷等级的划分来确定本次设计的供电方式以及整个系统的规划方案;2.先把设计的负荷计算出来,然后根据计算的负荷结果来选择出相应的导线的截面积和型号,还有穿线保护管的型号,断路器的型号,以及相关的电线电缆的选型;3.选择照明灯具,插座系统选择,以及其对应的安装高度还有导线的敷设方式;4.对住宅安全中防雷和接地安全方面的设计,最终得出本次设计的结果和结论。关于这次的课程设计,我们主要是偏重于所学的电气相关的基本的知识和基本的电气理论。本次设计还需按照相关的民用建筑设计规范来规划整体的设计思路,最终完成对负荷的计算,照度的计算,设备的选型,以及绘制相关的作业图,小区住宅的配电设计方案。
关键词:低压配电系统;负荷计算;、照度;防雷接地设计;设备选择
The Design of Residential 7-story Residential Low-voltage Distribution System
Abstract
The topic of this graduation design is of a District 7 story residential low-voltage distribution system design, does not consider the elevator design, each layer 4 households, each floor has three units, without considering the underground layer design, regardless of the roof decorative lighting design.?This graduation design course is mainly for residential electricity system to consider and design, the main content of the design is divided into four points: 1. according to the relevant rules and regulations on the load grade to determine the planning scheme of the design of the power supply and the whole system; 2. first calculated the design load, and then according to the calculation results of load to select the corresponding sectional area of wire and type, and wear line protection tube type, circuit breaker type, and the selection of wire and cable related; 3. choice of lighting, socket system selection, and the corresponding installation height and wire laying method; 4. the lightning protection residential security and grounding safety aspects of the design, finally the design results and conclusions.?Regarding thi
原创力文档


文档评论(0)