PRIUS(底盘)研讨.pptVIP

下载本文档

4
0
约2.67万字
约 72页
2016-08-06 发布于湖北
举报
版权申诉

PRIUS(底盘)研讨.ppt

1、本文档共72页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

PRIUS(底盘)研讨

* lj * lj * lj * When the 制动 system is failure, the switching solenoid valve (SSC) is closed and the fluid flow is shut off from the 主缸. lj * lj * Absolute angle type 转向 angle sensor is the same as AVENSIS and VERSO. Specified Value: 7.7 degrees * [Vehicle Condition] Shift lever is in P Parking 制动 is applied * Select ECB (Electronically Controlled 制动 system) Invalid Mode Perform the procedure listed below in 1 minute Turn the power switch to IG-ON with the shift lever in P and parking 制动 set Move the shift lever to N and then depress the 制动 pedal more than 8 times in 5 seconds Move the shift lever to P and then depress the 制动 pedal more than 8 times in 5 seconds Move the shift lever to N and then depress the 制动 pedal more than 8 times in 5 seconds Move the shift lever to P Check that the 制动 warning light (yellow) is blinking * * The structure is same as LS600hL_LS600h * Repair seal liquid has a useful life of 4 years. * * Brush type 动力转向 motor is used for –A and –K models 无电刷型动力转向 motor is used for –W, -Q and Mexico models, and models with 215/45R17 tires lj * 增压转换器 is provided in the 动力转向 ECU 增压转换器 converts the voltage of the battery and supplies the power source to the motor 动力转向 ECU uses the CAN protocol for diagnosis communication * lj * lj * [旋转角度传感器 Initialization and 扭矩传感器 Zero Point Calibration] Precondition Connect the tester (Techstream or Intelligent tester) to DLC3 Turn the power switch to IG-ON Turn the tester on Enter the following menu: Chassis / EMPS / Data List Check the values of the following item: IG Power SupplyStandard Voltage: 10 to 14 V Initialization and Calibration NOTICE: Initialization and calibration cannot be performed when DTCs (C1516 and C1526) are stored. Connect the tester (Techstream or Intelligent tester) to DLC3 Turn the power switch to IG-ON Turn the tester on Enter the following menu: Chassis / EMPS / Utility / 扭矩传感器 Adjustment [Assist Map Writing] NOTICE: If the DTC (C1581) is output after 扭矩传感器 zero point calibration, pe