C程序设计谭浩强课后习题答案.docVIP

习题4.8 #include stdafx.h #include stdio.h void main() {float pi = 3.14; // 定义pi float r, h; scanf(%f,%f, r, h);// 公式乘号“*”不能省略 float c = 2* pi * r; float s1 = pi * r *r; float s2 = 4.0 * pi * r * r; // 分数的书写，注意要使用浮点数进行运算。4/3要写成4.0/3，否则结果会出错 float v1 = 4.0 / 3 * pi * r * r *r; float v2 = pi * r * r * h ;// 注意，结果要“四舍五入” printf(半径为：r=%.2f\n, r); printf(高为：h=%.2f\n, h); printf(圆周长为：c=%.2f\n, c); printf(圆面积为：s1=%.2f\n, s1); printf(圆球表面积为：s2=%.2f\n, s2); printf(圆球体积为：v1=%.2f\n, v1); printf(圆柱体积为：v2=%.2f\n, v2); } 习题4.9 #include stdafx.h #include stdio.h void main() {float c , F; scanf(%f, F); c = 5.0 / 9.0 * (F - 32); printf(华氏度为：F=%.2f\n, F); printf(摄氏度为：c=%.2f\n, c); } 习题5.5 #include stdio.h void main() {float x, y; printf(请输入x的数值：\n); scanf(%f, x); if (x1) { y = x; } else if (x10) { y = 2 * x -1; } else { y = 3 * x - 11; } printf(函数值为：%f\n,y); } 习题5.6 #include stdio.h void main( ) {int s; printf(请输入分数s:); scanf(%d, s); switch(s/10) { case 10: case 9: printf(分数为 A\n); break; case 8: printf(分数为 B\n); break; case 7: printf(分数为 C\n); break; case 6: printf(分数为 D\n); break; default: printf(分数为 E\n); } } 习题5.7 #include stdio.h void main( ) { long int num; int count; int x1, x2, x3, x4, x5; printf(请输入整数(1-99999)：\n); scanf(%ld, num); if (num 99999 || num 1) { printf(输入错误！\n); } else { if (num 9999) { count = 5; } else if (num 999) { count = 4; } else if (num 99) { count = 3; } else if (num 9) { count = 2; } else { count = 1; } printf(%ld为%d位数\n, num, count); x1 = num / 10000; x2 = num % 10000 / 1000; x3 = num % 1000 / 100; x4 = num % 100 / 10; x5 = num % 10; switch (count) {  case 5: printf(每位数字为：%d,%d,%d,%d,%d\n, x1,x2,x3,x4,x5); printf(逆序为：%d%d%d%d%d\n, x5,x4,x3,x2,x1); break; case 4: printf(每位数字为：%d,%d,%d,%d\n, x2,x3,x4,x5); printf(逆序为：%d%d%d%d\n, x5,x4,x3,x2); break; case 3: printf(每位数字为：%d,%