Y型畅流铸钢截止阀.pptVIP

Flowserve - Edward Cast Valves- 爱德华铸造阀门 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 Y型畅流铸钢截止阀 爱德华铸钢截止阀 司太立21#合金密封面 爱德华铸钢截止阀 堆焊硬质合金的上密封面 爱德华铸钢截止阀 (改进的组合式压力密封垫片) 爱德华铸钢截止阀(阀体导向阀芯) Y型畅流铸钢截止阀Parallel Seating Y型畅流铸钢截止阀 Equiwedge Gate Valve Equiwedge Gate vs Parallel Slide Gate Valve Parallel Slide Edward do not offer parallel slide 2 gates in parallel moving into and out of engagement with the body seats Gates are keep in contact with seats by spring (or set of springs) or internal wedge mechanism Downstream gate is free to align to downstream seat and will seal as long as there is sufficient differential pressure across the valve Leakage may occur at very low DP e.g during low pressure start up Continous sliding contact between the gates and seats resulting in high wear and possible scoring under high DP Equiwedge Gate vs Parallel Slide Gate Valve In prototype tests, we found our Edward valves always opened with less than the design closing torque when exposed to extreme pipe-bending and severe thermal cycle (heat-up cool down) Body guides support the wedges. The seating surfaces of the wedge and seat are in sliding contact only through a small portion of the opening /closing travel (3%-5%). Thus minimize wear on seats Side loads are transferred from seats to body guides. Wear or scoring of body guides does not affect sealing We have tested the guiding system under “blowdown” services where high DP is applied across partially opened gates. 楔式双闸板闸阀 冲击手轮 给一个普通的手轮提供多次关闭力，保证绝对就座关闭，大尺寸的阀门允许一个人采用气动扳手操作。 止推轴承 减少力矩，消除偏心侧向载荷，延长阀门寿命。 阀杆导向轭架 防止阀杆转动，提供阀位指示 轭架 利于盘根拆装的结构空间。 轭架锁环 利于维修时的快速解体 阀帽压盖 提供作用于压力密封垫片上的密封载荷。 阀盖 精密加工，并带有硬质合金的阀杆上密封面，延长盘根寿命。 阀杆 带ACME螺纹，经精车并热处理以增强强度、硬度及耐磨性。 盘根系统 利用具有防推出圆环的柔软石墨填料，以做最佳的防漏，并经久耐用。 压力密封垫片 预加载荷，压力增强设计，供长期可靠的服务。 阀芯活塞 阀体导向，消除不对中，卡涩及阀杆弯曲的问题。 平衡管 连接阀芯上部区域与阀门出口，形成压力平衡。在较低的压差下，帮助阀芯升起，在回流情况下迅速关闭。减少阀芯的运动磨损。 导向肋 表面为硬质合金，提供阀芯的阀体导向 整体司太立21#合金密封面 阀座与阀芯的硬质合金密封